Windshield wipers and washer
Windshield wiper lever
Fig. 83 Operating the front windshield wipers.
Fig. 84 Operating the rear wiper.
The windshield wipers work only if the ignition is switched on and the engine hood is closed.
Move the lever to the desired position :
Wiper switched off.
Intermittent wiping for the front windshield. Rain sensor active (if equipped).
Slow wiper speed.
Fast wiper speed.
x One-tap wiping – brief wiping. Hold the lever down longer to wipe more often.
Pull the lever toward the steering wheel to activate the front windshield washers, then release.
Switch for adjusting the windshield wiper interval settings (vehicles without a rain sensor) or the sensitivity of the rain sensor (vehicles with a rain sensor).
Move the lever to the desired position :
Intermittent wiping for the rear window. The wiper wipes about every 6 seconds.
Press the lever forward as far as it will go to activate the rear window washers, then release to stay in intermittent wiping mode (position Ⓖ). Pull the lever toward the steering wheel to turn the rear wiper off.
- This feature can be turned on and off in the Vehicle settings menu in the Infotainment system .
WARNING
Windshield washer fluid without enough frost protection can freeze on the windshield and reduce visibility.
- Use the windshield washer system with enough frost protection for winter temperatures.
- Never use the windshield wipers/washers when it is freezing without first defrosting the windshield. The washer solution may freeze on the windshield and reduce visibility.
WARNING
Worn or dirty wiper blades reduce visibility and increase the risk of accidents and severe injuries.
- Always replace wiper blades that are worn, damaged, or do not keep the windshield clear .
NOTE
To help prevent damage to the wiper blades and the wiper motor when it is cold outside, always make sure that blades are not frozen to the windshield before switching on the ignition. Using the service position can be helpful in cold weather so the wipers do not freeze to the windshield .
- If the ignition is switched off while the wipers are running, the wipers will continue at the same wiping speed when the ignition is switched on again. Frost, ice, snow, leaves, and other objects on the windshield can damage the wipers and the wiper motor.
- Remove snow and ice from the wipers before you begin driving.
- If the wiper blades freeze to the windshield, loosen them carefully. Volkswagen recommends using a deicing spray.
NOTE
Never switch on the windshield wipers when the windshield is dry because the windshield can be scratched.
When the vehicle is not moving, the wiper speed changes temporarily to the next lower speed.
Certain settings are automatically saved by the driver personalization feature .
Windshield wiper functions
Heated washer nozzles (if equipped)
When the ignition is switched on, the heat applied to the washer nozzles is automatically regulated depending on the outside air temperature. The heating thaws frozen washer nozzles, but not the fluid supply hoses.
Wiper performance during intermittent wiping
Speed-dependent interval control: The higher the vehicle speed, the faster the wipers move.
Rain sensor
Fig. 85 Windshield wiper lever: Adjusting the rain sensor ① (if equipped).
Fig. 86 Inside the front windshield above the inside mirror: Sensitive rain sensor surface (arrows).
When switched on, the rain sensor automatically shortens or lengthens the time between wiping intervals depending on how hard it is raining .
Activating and deactivating the rain sensor
- Position Ⓐ: Rain sensor off (windshield wiper lever home position).
- Position Ⓑ: Rain sensor active - automatic wiping as needed.
After switching the ignition off and back on again, the rain sensor stays on and works again when the wiper lever is in position Ⓑ.
The automatic wipe function of the rain sensor can be turned on and off in the Vehicle settings menu in the Infotainment system .
Setting the rain sensor's sensitivity
The rain sensor's sensitivity can be adjusted manually .
- Move switch to the right – high sensitivity.
- Move switch to the left – low sensitivity.
WARNING
The rain sensor cannot always recognize rain and activate the wipers.
- Switch the wipers on manually when water on the windshield reduces visibility.
Tips and troubleshooting
When the ignition is switched on, several warning and indicator lights come on briefly for a function check. They go out after a few seconds.
Windshield washer fluid level too low
Your vehicle may be equipped with a yellow indicator light that comes on when the windshield washer fluid level is low.
Refill windshield washer reservoir at the next opportunity .
Rain and light sensor malfunction
The wipers do not switch on automatically if it rains, and the yellow indicator light comes on.
- Switch the ignition off and on again.
- If the indicator light comes on again and stays on, contact an authorized Volkswagen dealer or an authorized Volkswagen Service Facility .
Windshield wiper malfunction
The wipers do not wipe and the yellow indicator light comes on.
- Switch the ignition off and on again.
- If the indicator light comes on again and stays on, contact an authorized Volkswagen dealer or an authorized Volkswagen Service Facility .
If there are changes in the way the rain sensor works
The rain sensor may misread what is happening in the detection zone of its sensitive rain-sensor surface (arrows) and not work for a number of reasons, which may include:
- Worn out wiper blades: Worn out wiper blades may leave a film of water or wiping streaks; this can cause the wipers to run longer, to wipe more often, or to wipe continuously at high speed.
- Insects: Insects hitting the windshield may trigger the wipers.
- Salt streaks: Salt streaks on the windshield from winter driving can cause wiping more often or continuously on glass that is almost dry.
- Dirt: Caked-on dust, wax, any other buildup on the windshield (lotus effect), or car-wash detergent residue can lower the rain sensor's sensitivity and cause it to react too slowly or not at all. Clean the rain sensor's sensitive surface (arrows) regularly and check the wiper blades for wear or damage.
- Crack or chip in the windshield: If a stone hits and chips the windshield while the rain sensor is on, this will trigger a wiper cycle. After that, the rain sensor will recognize the change and recalibrate itself to respond to the sensitive surface's reduced detection zone. Depending on the size of the chip, the sensor's reaction pattern may or may not change.
To remove wax and coats of polish safely, Volkswagen recommends using an alcohol-based windshield cleaner.
WARNING
Failure to heed warning lights or other warnings can result in a collision and serious personal injury.
- Never ignore warning lights or text WARNINGS.
- Always stop the vehicle as soon as it is safe to do so.
NOTE
Failure to heed warning lights or text WARNINGS can result in vehicle damage.
If there is something on the windshield, the wiper will try to wipe it away. If it continues to block the wiper, the wiper will stop moving. Remove the obstacle and switch the wiper on again.
Download Manual