2020 Toyota Highlander Owners Manual - Multi-information display (with color display)

Multi-information display (with color display)

Display contents

Drive information

Select to display various drive data.

Navigation
systemlinked display (if equipped)

Select to display the following navigation system-linked information.

• Route guidance
• Compass display (north-up display/heading-up display)

Audio
system-linked display

Select to enable selection of an audio source or track on the meter using the meter control switches.

Dynamic radar cruise control
operation guide (if equipped)

Select to display operation procedures of the dynamic radar cruise control.

The  tab will
change to  when the
vehicle is in constant speed control mode. If activated, the operational status of the lda (lane departure alert) system will also be displayed. (If equipped)

Lda (lane
departure alert) operational status (if equipped)*

Select to display the operational status of the lda (lane departure alert). If activated, the operation procedures of the dynamic radar cruise control system will also be displayed. (If equipped) *: The lda operational status will not be displayed if the dynamic radar cruise control operation guide is displayed.

Warning message
display

Select to display warning messages and measures to be taken if a malfunction is detected.

Settings display

Select to change the meter display settings.

• Operating the meter control switches

   

1. Enter/set/reset
2. Select an item/change pages
3. Return to the previous screen
4. press: displays the screen registered as the top screen when no screen has been registered, the drive information screen will be displayed.

Press and hold: registers the currently displayed screen as the top screen

When the confirmation screen is displayed, select yes to register the screen. If the selected screen cannot be registered, a registration failure message will be shown.

Drive information

• Current fuel consumption*1 displays the current rate of fuel consumption
•  average fuel economy (after reset*2/after start/after refuel)*1 displays the average fuel economy since the function was reset, the engine was started, and the vehicle was refueled, respectively use the displayed average fuel economy as a reference.
•  Average vehicle speed (after reset*2/after start)*1 displays the average vehicle speed since the function was reset and the engine was started, respectively
•  elapsed time (after reset*2/after start)*1 displays the elapsed time since the function was reset and the engine was started, respectively
•  distance (driving range/after start/after reset*2)*1 displays the estimated maximum distance that can be driven with the quantity of fuel remaining and the distance driven after the engine was started, respectively.

•  this distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.
•  when only a small amount of fuel is added to the tank, the display may not be updated.

  When refueling, turn the engine switch off. If the vehicle is refueled without turning the engine switch off, the display may not be updated.

•  Eco driving indicator  
•  Awd control (if equipped)

Displays the torque distribution between the front and rear axles of the awd control system *1: can be registered to drive information 1 through 3. *2: Resetting procedures:

•  select a function to be reset using the meter control switches and then press and hold to reset.

Settings display

Changing the settings

1. Select  using
   the meter control switches.
2. Select an item and then set it with the center button.

Customizable items

• Language select to change the language on the display.
•  Units select to change the unit of measure for fuel consumption.
•  Maintenance system (for u.S.A.) Select to reset the maintenance data after the required maintenance is performed.
•  Eco driving indicator light select to activate/deactivate the eco driving indicator light.

   

   

•  Switch
  settings you can register 1 screen as the top screen. To register, press and hold while
  the desired screen is displayed.
•  Drive information 1 through 3 select to select up to 2 items that will be displayed on a drive information screen, up to 3 drive information screens can be set.
•  Pop-up display select to set the following pop-up displays, which may appear in some situations, on/off.

•  route guidance display of the navigation system-linked system (if equipped)
• incoming call display of the hands-free phone system
• cruise control operation display
• instrument panel brightness adjustment display

•  accent color select to change the accent colors on the screen, such as the cursor color.
• Speed limit display* select to set the display of speed limit information stored in the navigation system to on with the speed limit caution indicator (yellow) enabled, on with the speed limit caution not enabled, or off. If enabled, the speed limit caution indicator will come on if the vehicle speed exceeds the displayed speed limit.
•  Initialization registered or changed meter settings will be deleted or returned to their default setting.

Settings can be changed. (Customizable features: ) *: Speed limit display may not be available for some regions.

• Pop-up display

   

In some situations, such as when a switch operation is performed, a pop-up display, such as the operating cruise control switch, will be temporarily displayed on the multi-information display.

The pop-up display function can be set on/off.

• Setting display automatic cancelation

   

In the following situations, setting display in which the settings can be changed through the meter control switch will automatically be turned off.

• When a warning message appears while the setting display is displayed
• when the vehicle begins to move while the setting display is displayed

• Liquid crystal display

   

Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem continuing to use the display.

Warning   The information display at low temperatures   Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed. For example, there is a lag between the driver's shifting and the new gear number appearing on the display. This lag could cause the driver to downshift again, causing rapid and excessive engine braking and possibly an accident resulting in death or injury. Cautions during setting up the display   As the engine needs to be running during setting up the display, ensure that the vehicle is parked in a place with adequate ventilation. In a closed area such as a garage, exhaust gases including harmful carbon monoxide (co) may collect and enter the vehicle. This may lead to death or a serious health hazard.

Notice   During setting up the display   To prevent battery discharge, Ensure that the engine is running while setting up the display features.