Remote start — if equipped
All of the following conditions must be met before the engine will remote start:
-
Gear selector in PARK
-
Doors closed
-
Hood closed
-
Liftgate closed
-
Hazard switch off
-
Brake switch inactive (brake pedal not pushed)
-
Battery at an acceptable charge level
-
System not disabled from previous remote start event
-
Vehicle security alarm not active
-
Ignition in the OFF position
-
Malfunction Indicator Light (MIL) is not illuminated
WARNING:
-
Do not start or run an engine in a closed garage or confined area. Exhaust gas contains Carbon Monoxide (CO) which is odorless and colorless. Carbon Monoxide is poisonous and can cause serious injury or death when inhaled.
-
Keep key fobs away from children. Operation of the Remote Start System, windows, door locks or other controls could cause serious injury or death.
REMOTE START ABORT MESSAGE
The following messages will appear in the instrument cluster display if the vehicle fails to remote start or exits remote start prematurely if equipped with Remote Start:
-
Remote Start Cancelled — Door Open
-
Remote Start Cancelled — Hood Open
-
Remote Start Cancelled — Fuel Low
-
Remote Start Cancelled — L/Gate Open
-
Remote Start Disabled — Start Vehicle To Reset
The message stays active until the ignition is placed in the ON/RUN position.
TO ENTER REMOTE START MODE
Push and release the remote start button on the key fob twice within five seconds. The vehicle doors will lock, the parking lights will flash and the horn will chirp twice (if programmed). Then, the engine will start and the vehicle will remain in the Remote Start mode for a 15 minute cycle.
Note:
-
If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.
-
The park lamps will turn on and remain on during Remote Start mode.
-
For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode.
-
The engine can be started two consecutive times (two 15 minute cycles) with the key fob. However, the ignition must be placed in the ON/RUN position before you can repeat the start sequence for a third cycle.
TO EXIT REMOTE START MODE WITHOUT DRIVING THE VEHICLE
Push and release the remote start button one time or allow the engine to run for the entire 15 minute cycle.
Note:
To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid Remote Start request.
TO EXIT REMOTE START MODE AND DRIVE THE VEHICLE
Before the end of 15 minute cycle, push and release the unlock button on the key fob to unlock the doors and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.
Note:
The message “Push Start Button” will appear in the instrument cluster display until you push the START/STOP ignition button.
REMOTE START COMFORT SYSTEM — IF EQUIPPED
When Remote Start is activated, the driver heated seat feature will automatically turn on in cold weather. This feature will stay on through the duration of Remote Start or until the ignition switch is placed in the ON/RUN position.
The Remote Start Comfort system can be activated and deactivated through the Uconnect system. Refer to “Uconnect Settings” in “Multimedia” for further information on Remote Start Comfort system operation.
GENERAL INFORMATION
The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
-
This device may not cause harmful interference, and
-
This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d`Innovation, Science and Economic Development applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
-
l'appareil ne doit pas produire de brouillage, et
-
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
La operación de este equipo está sujeta a las siguientes dos condiciones:
-
es posible que este equipo o dispositivo no cause interferencia perjudicial y
-
este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Note:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Download Manual