Wipers and washers
A: Wiper speed control (front)
1. MIST / ˅ – Single wipe
2. OFF / O – Off
3. INT / --- – Intermittent wipe
AUTO* – Auto control wipe
4. LO / 1 – Low wiper speed
5. HI / 2 – High wiper speed
B: Intermittent control wipe time adjustment
C : Wash with brief wipes (front) *
D : Rear wiper/washer control *
6. HI / 2 – Continuous wipe
7. LO / 1 – Intermittent wipe*
8. OFF / O – Off
E : Wash with brief wipes (rear)
Windshield wipers
Operates as follows when the ignition switch is turned ON.
1. MIST/˅: For a single wiping cycle, move the lever to this (MIST/˅ ) position and release it. The wipers will operate continuously if the lever is held in this position.
2. OFF / O: Wiper is not in operation.
3. INT / ---: Wiper operates intermittently at the same wiping intervals. Use this mode in a light rain or mist. To vary the speed setting, turn the speed control knob.
4. LO / 1: Normal wiper speed
5. HI / 2: Fast wiper speed
NOTICE
If there is heavy accumulation of snow or ice on the windshield, defrost the windshield for about 10 minutes, or until the snow and/or ice is removed before using the windshield wipers to ensure proper operation. If you do not remove the snow and/or ice before using the wiper and wash-er, it may damage the wiper and washer system.
Auto control
The rain sensor (A) located on the upper end of the windshield glass senses the amount of rainfall and controls the wiping cycle for the proper interval. The more it rains, the faster the wiper operates. When the rain stops, the wiper stops.
To vary the speed setting, turn the speed control knob (1).
If the wiper switch is set in AUTO mode when the ignition switch is ON, the wiper will operate once to perform a selfcheck of the system. Set the wiper to OFF (O) position when the wiper is not in use.
CAUTION
When the ignition switch is ON and the windshield wiper switch is placed in the AUTO mode, use caution in the following situations to avoid any injury to the hands or other parts of the body:
- Do not touch the upper end of the windshield glass facing the rain sensor.
- Do not wipe the upper end of the windshield glass with a damp or wet cloth.
- Do not put pressure on the windshield glass.
CAUTION
- When washing the vehicle, set the wiper switch in the OFF (O) position to stop the auto wiper operation. The wiper may operate and be damaged if the switch is set in the AUTO mode while washing the vehicle.
- Do not remove the sensor cover located on the upper end of the passenger side windshield glass. Damage to system parts could occur and may not be covered by your vehicle warranty.
- When starting the vehicle in winter, set the wiper switch in the OFF (O) position. Otherwise, wipers may operate and ice may damage the windshield wiper blades. Always remove all snow and ice and defrost the windshield properly prior to operating the windshield wipers.
- When tinting the windshield, be careful of any fluid getting into the sensor located in the top center of the front windshield. It may damage the related parts.
Windshield washers
In the OFF (O) position, pull the lever gently toward you to spray washer fluid on the windshield and to run the wipers 1-3 cycles.
Use this function when the windshield is dirty.
The spray and wiper operation will continue until you release the lever.
If the washer does not work, check the washer fluid level. If the fluid level is not sufficient, you will need to add appropriate non-abrasive windshield washer fluid to the washer reservoir.
The reservoir filler neck is located in the front of the motor compartment on the passenger side.
CAUTION
To prevent possible damage to the washer pump, do not operate the washer when the fluid reservoir is empty.
WARNING
Do not use the washer in freezing temperatures without first warming the windshield with the defrosters; the washer solution could freeze on the windshield and obscure your vision.
CAUTION
- To prevent possible damage to the wipers or windshield, do not operate the wipers when the windshield is dry.
- To prevent damage to the wiper blades, do not use gasoline, kerosene, paint thinner, or other solvents on or near them.
- To prevent damage to the wiper arms and other components, do not attempt to move the wipers manually.
- To prevent possible damage to the wipers and washer system, use anti-freezing washer fluids in the winter season or cold weather.
Rear window wiper and washer switch
The rear window wiper and washer switch is located at the end of the wiper and washer switch lever. Turn the switch to the desired position to operate the rear wiper and washer.
1. HI / 2 - Normal wiper operation
2. LO / 1 - Intermittent wiper operation (if equipped)
3. OFF / O - Wiper is not in operation
Push the lever away from you to spray rear washer fluid and to run the rear wipers 1~3 cycles. The spray and wiper operation will continue until you release the lever.
Heated washer nozzle (if equipped)
The heated washer nozzle function defreeze the washer nozzles in freezing weather.
The heated washer nozzle will turn on and off automatically when the ignition switch is in ON or when the engine is running in following conditions:
- Turns ON when the outside temperature is below 5°C, and OFF when it is over 10°C.
- The washer fluid defreezing speed may be slower when the ignition is in ON, than compared to when the engine is running.
- When the ignition is in ON, after 20 minutes of operation, the system will turn off automatically to prevent possible battery discharge.
- After the engine is running, the washer fluid will defrost after 5 to 10 minutes.
- If the engine has been started within the operating temperature, the heated nozzle remains ON even after 20 minutes.
NOTICE
In below conditions, the heated washer nozzle may not function properly.
- The washer fluids in the washer reservoir is frozen.
- Outside temperature sensor is malfunctioning.
Download Manual