Operating the Switches Around the Steering Wheel
ENGINE START/STOP Button
■ Automatic Power Off If you leave the vehicle for 30 to 60 minutes with the transmission in 
*1 and the power mode in ACCESSORY, the vehicle automatically goes into the mode similar to
VEHICLE OFF (LOCK) to avoid draining the battery.
When in this mode:
The steering wheel does not lock.
You cannot lock or unlock doors with the remote transmitter or the smart entry with push button start system*.
Press the ENGINE START/STOP button twice to switch the mode to VEHICLE OFF (LOCK).
■ Power Mode Reminder If you open the driver’s door when the power mode is set to ACCESSORY, a warning buzzer sounds.
*1 : Automatic transmission/Continuously variable transmission models
Continued
uuOperating the Switches Around the Steering WheeluENGINE START/STOP Button
Warning buzzers may sound from inside and/ or outside the vehicle to remind you that the remote is out of the vehicle. If the buzzer continues even after the remote is put back inside, place it to be within its operational range.
If the remote is taken out of the vehicle, and the driver’s door is closed, a warning buzzer sounds from both inside and outside the vehicle. A warning message on the driver information interface notifies the driver inside that the remote is outside of the vehicle.
If the remote is taken out of the vehicle, and all the doors are closed, a warning buzzer sounds from outside the vehicle.
192
uuOperating the Switches Around the Steering WheeluTurn Signals
The turn signals can be used when the power mode is in ON.
When you lightly push up or down and release the turn signal lever, the exterior turn signals and turn signal indicator blink three times.
This feature can be used when signaling for a lane change.
193
uuOperating the Switches Around the Steering WheeluLight Switches
Rotating the light switch turns the lights on and off, regardless of the power mode setting.
Push the lever forward until you hear a click.
When in high beams, pull the lever back to return to low beams.
Pull the lever back, and release it.
Canadian models
Turn the lever to OFF either when:
.To turn the lights on again, turn the lever to OFF to cancel the lights off mode. Even if you do not cancel the lights off mode, the lights come on automatically when:
and the parking brake is released.194
uuOperating the Switches Around the Steering WheeluLight Switches
Automatic lighting control can be used when the power mode is in ON.
When you turn the light switch to AUTO, the headlights and other exterior lights will switch on and off automatically depending on the ambient brightness.
U.S. models
u You can change the auto light sensitivity setting.
2 Customized Features P. 372, 383
The headlights comes on when you unlock a door in dark areas with the headlight switch in AUTO.
u Once you lock the door, the headlights will go off.
Continued 195
uuOperating the Switches Around the Steering WheeluFog Lights*
The headlights automatically come on when the wipers are used several times within a certain number of intervals with the headlight switch in AUTO.
The headlights automatically go off a few minutes later if the wipers are stopped.
The headlights, all other exterior lights, and the instrument panel lights turn off 15 seconds after you set the power mode to VEHICLE OFF, take the remote with you, and close the driver’s door.
If you set the power mode to VEHICLE OFF with the headlight switch on, but do not open the door, the lights turn off after 10 minutes (three minutes, if the switch is in the AUTO position).
The lights turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. If you open the driver’s door, you will hear a lights on reminder chime.
When the low beam headlights are on, turn the fog light switch on to use the fog lights.
* Not available on all models
uuOperating the Switches Around the Steering WheeluDaytime Running Lights
The parking/daytime running lights come on when the following conditions have been met:
.The lights remain on even if you set the parking brake. Setting the power mode to VEHICLE OFF will turn off the daytime running lights.
The daytime running lights are off once the headlight switch is turned on, or when the head light switch is in AUTO and it is getting darker outside.
uuOperating the Switches Around the Steering WheeluAuto High-Beam
The front sensor camera detects the light sources ahead of the vehicle such as the lights of a preceding or oncoming vehicle, or street lights. When you are driving at night, the system automatically switches the headlights between low beam and high beam depending on the situation.
■ How to Use the Auto High-Beam When all of the following conditions have been met, the auto high-beam indicator comes on and the auto high-beam is activated.
• The power mode is in ON.
• The light switch is in AUTO.
• The lever is in the low beam position.
• The headlights have been automatically activated.
• It is dark outside the vehicle.
If the auto high-beam indicator does not come on even when all the conditions have been met, carry out the following procedure and the indicator will come on.
uuOperating the Switches Around the Steering WheeluAuto High-Beam
When auto-high beam is active, the headlights switch between high beam and low beam based on the following conditions.
If you want to manually switch the headlights between high beam and low beam, follow either of the procedures below. Note that when you do this, the auto high- beam indicator will turn off and the auto high-beam will be deactivated.
Pull the lever toward you for flashing the high beams then release it within about one second while driving.
u To reactivate the auto high-beam, pull the lever toward you for flashing the high beams then release it while driving. The auto high-beam indicator will come on.
Turn the light switch to .
u To reactivate the auto high-beam, turn the light switch to AUTO when the lever is in the low beam position, the auto high-beam indicator will come on.
Continued
uuOperating the Switches Around the Steering WheeluAuto High-Beam
■ How to Turn Off the Auto High-Beam You can turn the auto high-beam system off. If you want to turn the system off or on, set the power mode to ON, then carry out the following procedures while the vehicle is stationary.
With the light switch is in AUTO, pull the lever toward you and hold it for at least 40 seconds. After the auto high-beam indicator light blinks twice, release the lever.
With the light switch is in AUTO, pull the lever toward you and hold it for at least 30 seconds. After the auto high-beam indicator light blinks once, release the lever.
uuOperating the Switches Around the Steering WheeluWipers and Washers
The windshield wipers and washers can be used when the power mode is in ON.
■ MIST
The wipers run at high speed until you release the lever.
■ Wiper switch (OFF, INT*1/AUTO*2, LO, HI) Move the lever up or down to change the wiper settings.
Turn the adjustment ring to adjust the wiper operation.
Lower speed, fewer sweeps Higher speed, more sweeps
■ Washer
Sprays while you pull the lever toward you.
When you release the lever for more than one second, the spray stops, the wipers sweep two or three more times to clear the windshield, then stop.
*1: Models with manual intermittent operation
*2: Models with automatic intermittent operation
* Not available on all models
Continued
201
uuOperating the Switches Around the Steering WheeluWipers and Washers
When you push the lever down to AUTO, the windshield wipers sweep once, and go into the automatic mode.
The wipers operate intermittently, at low speed, or at high speed and stops in accordance with the amount of rainfall the rainfall sensor detects.
When the wiper function is set to AUTO, you can adjust the sensitivity of the rain fall sensor (using the adjustment ring) so that wipers will operate in accordance with your preference.
Low Sensitivity
High Sensitivity
* Not available on all models
uuOperating the Switches Around the Steering WheeluRear Defogger/Heated Door Mirror* Button
Press the rear defogger and heated door mirror button to defog the rear window and mirrors when the power mode is in ON.
The rear defogger and heated door mirrors automatically switch off after 10-30 minutes depending on the outside temperature.
However, if the outside temperature is 32°F (0°C) or below, it does not automatically switch off.
Canadian models
Press the heated windshield button to deice the windshield when the power mode is in ON.
uuOperating the Switches Around the Steering WheeluBrightness Control
When the power mode is in ON, you can use the brightness control dial to adjust instrument panel brightness.
Brighten: Turn the dial up.
Dim: Turn the dial down.
You will hear a beeper when the brightness reaches minimum or maximum. Several seconds after you have adjusted the brightness, you will be returned to the previous screen.
The brightness level is shown on the driver information interface while you are adjusting it.
204
uuOperating the Switches Around the Steering WheeluBrightness Control
When the head-up display is on, press and hold the HUD button until its brightness level indicator on the driver information interface. Brighten: Press the button.
Dim: Press the button.
Several seconds after you have adjusted the brightness, you will be returned to the previous screen.
The brightness level is shown on the driver information interface while you are adjusting it.
uuOperating the Switches Around the Steering WheeluDriving Position Memory System*
You can store two driver’s seat positions (except for power lumbar) with the driving position memory system.
When you unlock and open the driver's door with a remote transmitter, or smart entry system to one of the two preset positions and the seat adjusts to retracted positions of one of the two preset positions automatically.
The seat will move to the stored position when you set the power mode to ACCESSORY.
When you enter the vehicle, the driver information interface briefly shows you which remote transmitter you used to unlock the vehicle.
The driver’s seat moves rearward depending on the set seating position once you
.Once the power mode is in the ACCESSORY position, the driver’s seat moves forward to the DRIVER 1 or 2 preset position.
* Not available on all models
uuOperating the Switches Around the Steering WheeluDriving Position Memory System*
■ Storing a Position in Memory
u You will hear the beeper, and the memory button indicator light will blink.
memorized, the indicator light on the button you pressed stays on and you will hear two beeps.
.u You will hear a beep, and the indicator light will blink.
The seat will automatically move to the memorized position. When it has finished moving, you will hear a beep, and the indicator light stays on.
uuOperating the Switches Around the Steering WheeluAdjusting the Steering Wheel
The steering wheel height and distance from your body can be adjusted so that you can comfortably grip the steering wheel in an appropriate driving posture.
u The steering wheel adjustment lever is under the steering column.
u Make sure you can see the instrument panel gauges and indicators.
u After adjusting the position, make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
Download Manual