Connecting Bluetooth®
Preparations to use wireless communica-
tion
The following can be performed using Bluetooth® wireless com-
munication:
A portable audio player can be operated and listened to via
multimedia system
Hands-free phone calls can be made via a cellular phone
In order to use wireless communication, register and connect a
Bluetooth® device by performing the following procedures.
About Bluetooth®
The Bluetooth® word mark and logos are
registered trademarks owned Bluetooth
SIG, Inc. and any use of such marks by
Panasonic Corporation is under license.
Other trademarks and trade names are
those of their respective owners.
Certification
For vehicles sold in the U.S.A.
FCC ID: ACJ932YEAP01A727
NOTE:
<§15.19(a)(3)> This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired operation.
FCC WARNING:
<§15.21> Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
CAUTION:
<§2.1091> Radio frequency radiation exposure information:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body. This
transmitter must not be co-located or operating in conjuction with any other
antenna or transmitter.
349
For vehicles sold in Canada
NOTE:
This device complies with Industry Canada licence-exempt RSS stan-
dard(s). Operation is subject to the following two conditions: (1) this device
may not cause interference, and (2) this device must accept any interfer-
ence, including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, màªme si le brouillage est susceptible d’en compromettre le
fonctionnement.
NOTE:
This radio transmitter (identify the device by certification number, or model
number if Category II) has been approved by Industry Canada to operate
with the antenna types listed below with the maximum permissible gain and
required antenna impedance for each antenna type indicated. Antenna
types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (identifier le dispositif par son numéro de certifi-
cation ou son numéro de modèle s’il fait partie du matériel de catégorie II) a
été approuvé par Industrie Canada pour fonctionner avec les types
d’antenne énumérés ci-dessous et ayant un gain admissible maximal et
l’impédance requise pour chaque type d’antenne. Les types d’antenne non
inclus dans cette liste, ou dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l’exploitation de l’émetteur.
5
350
Access to http://www.ptc.panasonic.eu/,enter the below Model No. into the
keyword search box, you can download the latest “DECLARATION of CON-
FORMITY” (DoC).
Model No. YEAP01D104
351
Device registration/connection flow
1. Register the Bluetooth® device to be used with multimedia
2. Connect the Bluetooth® device to be used
To be used for audio
To be used for hands-free
phone
3. Start Bluetooth® connec-
3. Start Bluetooth® connec-
5
4. Check connection status
4. Check connection status
5. Use Bluetooth® audio
5. Use Bluetooth® phone
352
Registering and connecting from the “Bluetooth Setup” screen
To display the screen shown below, press the “SETUP” button and
select “Bluetooth” on the “Setup” screen.
Select to connect the device to
1
be used with multimedia sys-
Select to register a Bluetooth®
2
device to be used with multime-
Select
to
set
detailed
3
4
Bluetooth® system settings.
353
®
Registering a Bluetooth audio player for
the first time
To use the Bluetooth® Audio, it is necessary to register an audio
player with the system.
Once the player has been registered, it is possible to use the
Bluetooth® Audio.
This operation cannot be performed while driving.
Turn the Bluetooth® connection setting of your audio player on.
1
This function is not available when the Bluetooth® connection setting of
your audio player is set to off.
Press the “AUDIO” button.
2
Select “
Audio” on the “Select Audio Source” screen.
Follow the steps in “How to registering a Bluetooth® device” from
3
4
5
2
354
®
Registering a Bluetooth phone for the first
time
To use the hands-free system, it is necessary to register a
Bluetooth® phone with the system.
Once the phone has been registered, it is possible to use the
hands-free system.
Turn the Bluetooth® connection setting of your cellular phone on.
1
Press the
button.
2
3
4
Select “YES” to register a phone.
Follow the steps in “How to registering a Bluetooth® device” from
step
3
355
Registering a Bluetooth® device
Bluetooth® compatible phones (HFP) and portable audio players
(AVP) can be registered simultaneously. You can register up to 5
Bluetooth® devices.
How to register a Bluetooth® device
1
Select “Add”.
2
When this screen is displayed,
3
search for the device name dis-
played on this screen on the
screen of your Bluetooth®
device.
For details about operating the
®
Bluetooth device, see the manual
that comes with it.
5
To cancel the registration, select
“Cancel”.
®
®
Register the Bluetooth device using your Bluetooth device.
4
A PIN-code is not required for SSP (Secure Simple Pairing) compatible
®
®
Bluetooth devices. Depending on the type of Bluetooth device being
connected, a message confirming registration may be displayed on the
®
®
Bluetooth device’s screen. Respond and operate the Bluetooth device
according to the confirmation message.
Check that this screen is dis-
played when registration is
complete.
5
356
Select “OK” when the connection status changes from “Connect-
ing...” to “Connected”.
6
If an error message is displayed, follow the guidance on the screen to try
again.
Registration can be performed from screens other than the “Bluetooth
Setup” screen.
When registering from the “Bluetooth Audio” screen
1
Select “Select Device”.
2
Follow the steps in “How to registering a Bluetooth® device” from
3
step
2
Deleting a Bluetooth® device
1
Select “Remove”.
2
Select the desired device.
3
A confirmation message will be displayed, select “Yes” to delete the
4
device.
Check that a confirmation screen is displayed when the operation is
5
complete.
357
Connecting a Bluetooth® device
Up to 5 Bluetooth® devices (Phones (HFP) and audio players
(AVP)) can be registered.
If more than 1 Bluetooth® device has been registered, select
which device to connect to.
Press the “SETUP” button.
1
Select “Bluetooth” on the “Setup” screen.
2
Select the device to be con-
3
nected.
Supported profile icons will be dis-
played.
Phone
1
Audio player
2
Supported profile icons for cur-
rently connected devices will illumi-
nate.
5
Dimmed icons can be selected to connect to the function directly.
Auto connection
To turn auto connection mode on, set “Bluetooth Power” to on.
When you register a phone, auto connection will be activated. Always
set it to this mode and leave the Bluetooth® phone in a place where a
connection can be established.
When the engine switch is turned to the “ACC” or “ON” position, the sys-
tem will search for a nearby cellular phone you have registered.
Next, the system automatically connects with the most recent of the
phones connected to in the past. Then, the connection result is displayed.
358
Manual connection
When auto connection has failed or “Bluetooth Power” is turned off,
you must connect the Bluetooth® device manually.
Follow the steps in “Connecting a Bluetooth® device” from step
.
1
Connecting a Bluetooth® audio player
Registering an additional device
Select “Select Device” on the “Bluetooth Audio” screen.
1
2
Selecting a registered device
Select “Select Device” on the “Bluetooth Audio” screen.
1
2
Reconnecting a Bluetooth® phone
If the system cannot connect due to poor signal strength with the engine
switch in the “ACC” or “ON” position, the system will automatically attempt to
reconnect.
®
If the system is attempting to connect to a Bluetooth phone and the Blue-
®
tooth phone is turned off and then back on, the system will attempt to recon-
nect.
359
Displaying a Bluetooth® device details
You can confirm and change the registered device details.
Bluetooth® device registration status
1
Select the device.
2
Select “Device Info”.
3
Following screen is displayed:
4
Device name
1
Change connection method
2
Bluetooth® address
3
Display your telephone num-
4
ber
5
The number may not be dis-
played depending on the model
of phone.
Compatibility profile of the
5
device
Restore default settings
6
Changing connection method
Select “Connect Audio Player from”.
1
Select “Vehicle” or “Device”.
2
“Vehicle”: Connect the multimedia system to the portable audio player.
“Device”: Connect the portable audio player to the multimedia system.
360
Detailed Bluetooth® system settings
You can confirm and change the detailed Bluetooth® settings.
How to check and change detailed Bluetooth® settings
1
Select “System Settings”.
2
The following screen is displayed:
3
Bluetooth® power on/off
1
You can change Bluetooth®
function on/off
Bluetooth® name
2
3
Bluetooth® address
4
Display phone status
5
You can set the system to show
the status confirmation display
when connecting a telephone
Display audio player status
6
You can set the system to show
the status confirmation display
when connecting an audio
player
Compatibility profile of the system
7
Restore default settings
8
Editing the Bluetooth® PIN
You can change the PIN-code that is used to register your Bluetooth®
devices in the system.
Select “Bluetooth PIN”.
1
Input a PIN-code, and select “OK”.
2
Download Manual