Memory seat (if so equipped)
Pre-driving checks and adjustments 3-39
MEMORY STORAGE FUNCTION Two positions for the driver’s seat, steering wheel (if so equipped), and outside mirrors can be stored in the memory seat system. Follow these procedures to use the memory system. 1. Adjust the driver's seat, steering wheel (if
so equipped), and outside mirrors to the desired positions by manually operating each adjusting switch. For additional in- formation, see “Seats” (P. 1-2) and “Steer- ing wheel” (P. 3-33) and “Outside mirrors” (P. 3-37).
2. Push the SET switch and, within 5 sec- onds, push the memory switch (1 or 2).
3. The indicator light for the pushed memory switch will come on and stay on for approximately 5 seconds.
4. The chime will sound when the memory is stored.
NOTE: If a new memory position is stored in the same memory switch, the previous memory position will be overwritten by the new stored position.
Linking a key fob to a stored memory position Each key fob can be linked to a stored memory position (memory switch 1 or 2) with the following procedure. 1. Follow steps 1-3 in the “Memory storage
function” section for storing the memory position.
2. The indicator light for the pushed memory switch will come on. While the indicator light is on for 5 seconds, press the button on the key fob. The haz- ard lights will flash once and memory switch will click twice. After the indictor light goes off, the key fob is linked to that memory setting.
Once it is linked, when the ignition switch is in the OFF position, pressing the but- ton on the key fob will move the driver’s seat, steering wheel and outside mirrors to the linked memory switch position.
NOTE: If a new memory position is stored in the linked memory switch, then the key fob will link the new position and overwrites the previous position.
Confirming memory storage • Push the SET switch. • If a memory position has been stored in
the switch (1 or 2) then the indicator light for the respective switch will stay on for approximately 5 seconds.
LPD3165
3-40 Pre-driving checks and adjustments
ENTRY/EXIT FUNCTION This system is designed so that the driver's seat and steering wheel will automatically move when the shift position is in the P (Park). This allows the driver to easily get in and out of the driver’s seat. The driver’s seat will slide backward and the steering wheel will move up: • When the driver’s door is opened with the
ignition switch in the OFF position. • When the ignition switch is changed from
ACC to OFF with the driver’s door open. The driver’s seat and steering wheel will return to the previous position: • When the ignition switch is changed from
ACC or ON while the shift position is in the P (Park).
The entry/exit function can be adjusted or canceled through “Vehicle Settings” in the vehicle information display by performing the following: • Switch the Exit Seat Slide from on to off. • Switch the Exit Steering UP from on to off.
Restarting the entry/exit function If the battery cable is disconnected or if the fuse opens, the stored memory positions may be lost and some of the functions will be restricted. 1. Drive the vehicle over 25 mph (40 km/h). OR 2. Open and close the driver's door more
than two times with the ignition switch in the OFF position.
The entry/exit function should now work properly. SETTING MEMORY FUNCTION The position of the following settings can be linked to the Intelligent Key and the memorized settings can be available for each Intelligent Key. • Climate control system • Audio system To use the memory function, set the cli- mate and audio systems to the driver's preferred settings. Lock the doors with the Intelligent Key. Each Intelligent Key may be set with the driver's individual preferences. When a new Intelligent Key is used, “Con- nection with the key has been done” will be
displayed on the vehicle information dis- play and the memorized settings are available. To engage the memorized settings, per- form the following: 1. Carry the Intelligent Key that is linked to
the memorized settings. 2. Unlock the doors by wrapping hand
around the capacitive door handle or the button on the Intelligent Key.
3. Place the ignition switch in the ON posi- tion. The settings linked to the Intelligent Key will start.
For additional information on using the cli- mate control system, see “Heater and air conditioner (automatic)” (P. 4-33). SYSTEM OPERATION The memory seat system will not work or will stop operating under the following conditions: • When the vehicle speed is above 4 mph (7
km/h). • When any of the memory switches are
pushed while the memory seat is operating.
Pre-driving checks and adjustments 3-41
• When the switch for the driver’s seat and steering wheel is pushed while the memory seat is operating.
• When the seat has already been moved to the memorized position.
• When no seat position is stored in the memory switch.
• When the shift position is moved from P (Park) to any other position.
Download Manual