Uconnect phone — if equipped
Uconnect Phone is a voice-activated, hands-free, in-vehicle communications system. Uconnect Phone allows you to dial a phone number with your mobile phone* using simple voice commands (e.g., “Call” “Mike” “Work” or “Dial” “248-555-1212”). Your mobile phone’s audio is transmitted through your vehicle’s audio system; the sys- tem will automatically mute your radio when using the Uconnect Phone.
NOTE: The Uconnect Phone requires a mobile phone equipped with the Bluetooth “Hands-Free Profile,” Version 0.96 or higher. See the Uconnect website for supported phones. For Uconnect customer support:
• U.S. residents - visit UconnectPhone.com or call 1-877- 855-8400 (24 hours a day 7 days a week).
• Canadian Residents - visit UconnectPhone.com or call 1-800-465-2001 (English) or 1-800-387-9983 (French).
• Mon. – Fri., 8:00 am – 8:00 pm, ET • Sat., 9:00 am – 5:00 pm, ET • Sun., Closed Uconnect Phone allows you to transfer calls between the system and your mobile phone as you enter or exit your vehicle and enables you to mute the system’s microphone for private conversation. The Uconnect Phone is driven through your Bluetooth “Hands-Free Profile” mobile phone. Uconnect features Bluetooth technology - the global standard that enables different electronic devices to connect to each other with- out wires or a docking station, so Uconnect Phone works no matter where you stow your mobile phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect Phone. The Uconnect Phone allows up to seven mobile phones to be linked to the system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in English, Spanish, or French languages.
The Uconnect Phone is driven through your Bluetooth “Hands-Free Profile” mobile phone. Uconnect features Bluetooth technology - the global standard that enables different electronic devices to connect to each other with- out wires or a docking station, so Uconnect Phone works no matter where you stow your mobile phone (be it your purse, pocket, or briefcase), as long as your phone is turned on and has been paired to the vehicle’s Uconnect Phone. The Uconnect Phone allows up to seven mobile phones to be linked to the system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in English, Spanish, or French languages.
WARNING! ALWAYS drive safely with your hands on the wheel. You have full responsibility and assume all risks related to the use of the Uconnect features and appli- cations in this vehicle. Only use Uconnect when it is safe to do so. Failure to do so may result in an accident involving serious injury or death.
Uconnect Phone Button
The radio or steering wheel controls (if equipped) will contain the two control buttons (Uconnect Phone button and Voice Command but- ton) that will enable you to access the system. When you push the button you will hear the word Uconnect followed by a BEEP. The beep is your signal to give a command.
NOTE: The driver side upper windshield trim contains the microphone for the Uconnect Phone.
Voice Command Button
WARNING! Any voice commanded system should be used only in safe driving conditions following all applicable laws. Your attention should be focused on safely operating the vehicle. Failure to do so may result in a collision causing serious injury or death.
Actual button location may vary with the radio. The individual buttons are described in the “Op- eration” section.
The Uconnect Phone can be used with any Hands-Free Profile certified Bluetooth mobile phone. See the Uconnect website for supported phones. Refer to your mobile service provider or the phone manufacturer for details. The Uconnect Phone is fully integrated with the vehicle’s audio system. The volume of the Uconnect Phone can be adjusted either from the radio volume control knob or from the steering wheel radio control (right switch), if so equipped. The radio display will be used for visual prompts from the Uconnect Phone such as “CELL” or caller ID on certain radios. Operation Voice commands can be used to operate the Uconnect Phone and to navigate through the Uconnect Phone menu structure. Voice commands are required after most Uconnect Phone prompts. You will be prompted for a specific command and then guided through the available options. • Prior to giving a voice command, one must wait for the beep, which follows the “Ready” prompt or another prompt.
• For certain operations, compound commands can be used. For example, instead of saying “Setup” and then “Phone Pairing,” the following compound command can be said: “Setup Phone Pairing.”
• For each feature explanation in this section, only the compound form of the voice command is given. You can also break the commands into parts and say each part of the command when you are asked for it. For example, you can use the compound form voice command “Phonebook New Entry,” or you can break the com- pound form command into two voice commands: “Phonebook” and “New Entry.” Please remember, the Uconnect Phone works best when you talk in a normal conversational tone, as if speaking to someone sitting a few feet/meters away from you.
Voice Command Tree
Refer to “Voice Tree” in this section.
Help Command
If you need assistance at any prompt, or if you want to know your options at any prompt, say “Help” following the beep. The Uconnect Phone will play all the options at any prompt if you ask for help.
To activate the Uconnect Phone from idle, simply push the Phone button and follow the audible prompts for directions. All Uconnect Phone sessions begin with a push of the Phone button on the faceplate.
Cancel Command
At any prompt, after the beep, you can say “Cancel” and you will be returned to the main menu. However, in a few instances the system will take you back to the previous menu.
Pair (Link) Uconnect Phone To A Mobile Phone
To begin using your Uconnect Phone, you must pair your compatible Bluetooth enabled mobile phone. To complete the pairing process, you will need to reference your mobile phone Owner’s Manual. The Uconnect web- site may also provide detailed instructions for pairing. The following are general phone to Uconnect Phone pair- ing instructions: • Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Setup Phone Pairing.” • When prompted, after the beep, say “Pair a Phone” and follow the audible prompts.
• You will be asked to say a four-digit Personal Identifi- cation Number (PIN), which you will later need to enter into your mobile phone. You can enter any four-digit PIN. You will not need to remember this PIN after the initial pairing process.
• For identification purposes, you will be prompted to give the Uconnect Phone a name for your mobile phone. Each mobile phone that is paired should be given a unique phone name.
• You will then be asked to give your mobile phone a priority level between one and seven, with one being the highest priority. You can pair up to seven mobile phones to your Uconnect Phone. However, at any given time, only one mobile phone can be in use, connected to your Uconnect System. The priority allows the Uconnect Phone to know which mobile phone to use if multiple mobile phones are in the vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the Uconnect Phone will use the priority three mobile phone when you make a call. You can select to use a lower priority mobile phone at any time (refer to “Advanced Phone Connectivity” in this section).
Dial By Saying A Number
• Push the Phone button to begin.
• After the “Ready” prompt and the following beep, say “Dial.”
• The system will prompt you to say the number you want to call. • For example, you can say “234-567-8901.”
• The Uconnect Phone will confirm the phone number and then dial. The number will appear in the display of certain radios.
Call By Saying A Name
• Push the Phone button to begin.
• After the “Ready” prompt and the following beep, say “Call.”
• The system will prompt you to say the name of the person you want to call.
• After the “Ready” prompt and the following beep, say the name of the person you want to call. For example, you can say “John Doe,” where John Doe is a previously stored name entry in the Uconnect phonebook or down- loaded phonebook. To learn how to store a name in the phonebook, refer to “Add Names To Your Uconnect Phonebook,” in this section.
• The Uconnect system will confirm the name and then dial the corresponding phone number, which may ap- pear in the display of certain radios.
Phonebook Download – Automatic Phonebook Transfer From Mobile Phone
If equipped and specifically supported by your phone, Uconnect Phone automatically downloads names (text names) and number entries from your mobile phone’s phonebook. Specific Bluetooth Phones with Phone Book Access Profile may support this feature. See Uconnect website for supported phones. • To call a name from downloaded (or Uconnect) Phonebook, follow the procedure in “Call by Saying a Name” section.
• Automatic download and update, if supported, begins as soon as the Bluetooth wireless phone connection is made to the Uconnect Phone, for example, after you start the vehicle.
• A maximum of 1,000 entries per phone will be down- loaded and updated every time a phone is connected to the Uconnect Phone.
• Depending on the maximum number of entries down- loaded, there may be a short delay before the latest downloaded names can be used. Until then, if available, the previous downloaded phonebook is available for use.
• Only the phonebook of the currently connected mobile phone is accessible.
• Only the mobile phone’s phonebook is downloaded. SIM card phonebook is not part of the Mobile phone- book.
• This downloaded phonebook cannot be edited or de- leted on the Uconnect Phone. These can only be edited on the mobile phone. The changes are transferred and updated to Uconnect Phone on the next phone connec- tion.
Add Names To Your Uconnect Phonebook
NOTE: Adding names to the Uconnect Phonebook is recommended when the vehicle is not in motion. • Push the Phone button to begin.
• After the “Ready” prompt and the following beep, say “Phonebook New Entry.”
• When prompted, say the name of the new entry. Use of long names helps the Voice Command and it is recom- mended. For example, say “Robert Smith” or “Robert” instead of “Bob.”
• When prompted, enter the number designation (e.g., “Home,” “Work,” “Mobile,” or “Other”). This will allow you to store multiple numbers for each phonebook entry, if desired.
• When prompted, recite the phone number for the phone- book entry that you are adding.
After you are finished adding an entry into the phonebook, you will be given the opportunity to add more phone numbers to the current entry or to return to the main menu. The Uconnect Phone will allow you to enter up to 32 names in the phonebook with each name having up to four associated phone numbers and designations. Each lan- guage has a separate 32-name phonebook accessible only in that language. In addition, if equipped and supported by your phone, Uconnect Phone automatically downloads your mobile phone’s phonebook.
Edit Uconnect Phonebook Entries
• Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Phonebook Edit.” • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or other) that you wish to edit. • When prompted, recite the new phone number for the phonebook entry that you are editing. After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in the phonebook, call the number you just edited, or return to the main menu. NOTE: • Editing names in the phonebook is recommended when the vehicle is not in motion. • Automatic downloaded phonebook entries cannot be deleted or edited. “Phonebook Edit” can be used to add another phone number to a name entry that already exists in the phone- book. For example, the entry John Doe may have a mobile and a home number, but you can add “John Doe’s” work number later using the “Phonebook Edit” feature. Delete Uconnect Phonebook Entry NOTE: Editing phonebook entries is recommended when the vehicle is not in motion. To delete a Uconnect phonebook entry using Voice Com- mands:
1. Push the Phone button to begin.
2. After the “Ready” prompt and the following beep, say “Phonebook Delete.”
3. After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish to delete. You can either say the name of a phonebook entry that you wish to delete, or you can say “List Names” to hear a list of the entries in the phonebook from which you choose. To select one of the entries from the list, push the Voice Command button while the Uconnect Phone is playing the desired entry and say “Delete.”
4. After you enter the name, the Uconnect Phone will ask you which designation you wish to delete: home, work, mobile, other, or all. Say the designation you wish to delete. • Note that only the phonebook entry in the current language is deleted.
OTE: Automatic downloaded phonebook entries cannot be deleted or edited.
List All Names In The Uconnect Phonebook
• Push the Phone button to begin. • After the “Ready” prompt and the following beep, say
“Phonebook List Names.” • The Uconnect Phone will play the names of all the
phonebook entries, including the downloaded phone- book entries, if available.
• To call one of the names in the list, push the Voice Command button during the playing of the desired name, and say “Call.”
NOTE: The user can also exercise “Edit” or “Delete” operations at this point. • The Uconnect Phone will then prompt you as to the
number designation you wish to call.
• The selected number will be dialed.
Phone Call Features
The following features can be accessed through the Uconnect Phone if the feature(s) are available on your mobile service plan. For example, if your mobile service plan provides three-way calling, this feature can be ac- cessed through the Uconnect Phone. Check with your mobile service provider for the features that you have.
Answer Or Reject An Incoming Call — No Call Currently In Progress
When you receive a call on your mobile phone, the Uconnect Phone will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call. Push the Phone button to accept the call. To reject the call, push and hold the Phone button until you hear a single beep, indicating that the incoming call was re- jected.
Answer Or Reject An Incoming Call — Call Currently In Progress
If a call is currently in progress and you have another incoming call, you will hear the same network tones for call waiting that you normally hear when using your mobile phone. Push the Phone button to place the current call on hold and answer the incoming call.
NOTE: The Uconnect Phone compatible phones in the market today do not support rejecting an incoming call when another call is in progress. Therefore, the user can only answer an incoming call or ignore it.
Making A Second Call While Current Call Is In Progress
To make a second call while you are currently on a call, push the Voice Command button and say “Dial” or “Call” followed by the phone number or phonebook entry you wish to call. The first call will be on hold while the second call is in progress. To go back to the first call, refer to “Toggling Between Calls” in this section. To combine two calls, refer to “Conference Call” in this section.
Place/Retrieve A Call From Hold
To put a call on hold, push the Phone button until you hear a single beep. This indicates that the call is on hold. To bring the call back from hold, push and hold the Phone button until you hear a single beep.
Toggling Between Calls
If two calls are in progress (one active and one on hold), push the Phone button until you hear a single beep, indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at a time. Conference Call When two calls are in progress (one active and one on hold): 1. Push and hold the Phone button until you hear a
double beep, indicating that the two calls have been joined into one conference call.
Three-Way Calling
To initiate three-way calling, push the Voice Command button while a call is in progress, and make a second phone call, as described under “Making a Second Call While Current Call is in Progress.” After the second call has established, push and hold the Phone button until you hear a double beep, indicating that the two calls have been joined into one conference call.
Call Termination To end a call in progress: 1. Momentarily push the Phone button.
• Only the active call(s) will be terminated and if there is a call on hold, it will become the new active call. If the active call is terminated by the phone far end, a call on hold may not become active automatically. This is cell phone-dependent.
2. To bring the call back from hold, push and hold the Phone button until you hear a single beep.
Redial
To redial the last number called from your mobile phone using Voice Command:
1. Push the Phone button to begin.
2. After the “Ready” prompt and the following beep, say “Redial.” • The Uconnect Phone will call the last number that was dialed from your mobile phone.
NOTE: This may not be the last number dialed from the Uconnect Phone.
Call Continuation
Call continuation is the progression of a phone call on the Uconnect Phone after the vehicle ignition has been switched to OFF. Call continuation functionality available on the vehicle can be any one of three types: 1. After the ignition is switched to OFF, a call can continue on the Uconnect Phone either until the call ends, or until the vehicle battery condition dictates cessation of the call on the Uconnect Phone and transfer of the call to the mobile phone.
2. After the ignition is cycled to OFF, a call can continue on the Uconnect Phone for a certain duration, after which the call is automatically transferred from the Uconnect Phone to the mobile phone.
3. An active call is automatically transferred to the mobile phone after the ignition is cycled to OFF.
Uconnect Phone Features Language Selection
To change the language that the Uconnect Phone is using: • Push the Phone button to begin.
• After the “Ready” prompt and the following beep, say the name of the language you wish to switch to English, Espanol, or Francais.
• Continue to follow the system prompts to complete the language selection.
After selecting one of the languages, all prompts and voice commands will be in that language.
NOTE: After every Uconnect Phone language change operation, only the language-specific 32-name phonebook is usable. The paired phone name is not language-specific and usable across all languages.
Emergency Assistance
If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the Uconnect Phone is operational, you may reach the emergency number as follows: • Push the Phone button to begin.
• After the “Ready” prompt and the following beep, say “Emergency” and the Uconnect Phone will instruct the paired mobile phone to call the emergency number.
NOTE:
• The emergency number dialed is based on the country where the vehicle is purchased (911 for the U.S. and Canada and 060 for Mexico). The number dialed may not be applicable with the available mobile service and area.
• If supported, this number may be programmable on some systems. To do this, push the Phone button and say “Setup,” followed by “Emergency.”
• The Uconnect Phone does slightly lower your chances of successfully making a phone call as to that for the mobile phone directly.
WARNING! To use your Uconnect Phone System in an emergency, your mobile phone must be: • Turned on. • Paired to the Uconnect System. • Have network coverage.
Roadside Assistance/Towing Assistance
If you need roadside assistance: • Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Towing Assistance.”
NOTE: You should program the desired Towing Assistance phone number using the Voice Command system. To do this, push the Phone button and say “Setup,” fol- lowed by “Towing Assistance.” When prompted say 1-800-521-2779 for U.S., 1-800-363-4869 for Canada, 55-14-3454 for Mexico City and 1-800-712-3040 for out- side Mexico City in Mexico.
Paging
To learn how to page, refer to “Working With Automated Systems.” Paging works properly except for pagers of certain companies, which time out a little too soon to work properly with the Uconnect Phone.
Voice Mail Calling
To learn how to access your voice mail, refer to “Working With Automated Systems.”
Working With Automated Systems
This method is used in instances where one generally has to press numbers on the mobile phone keypad while navigating through an automated telephone system. You can use your Uconnect Phone to access a voice mail system or an automated service, such as a paging service or automated customer service line. Some services require immediate response selection. In some instances, that may be too quick for use of the Uconnect Phone. When calling a number with your Uconnect Phone that normally requires you to enter in a touch-tone sequence on your mobile phone keypad, you can push the Voice Com- mand button and say the sequence you wish to enter, followed by the word “Send.” For example, if required to enter your PIN followed with a pound, (3 7 4 6 #), you can push the Voice Command button and say, “3 7 4 6 # Send.” Saying a number, or sequence of numbers, followed by “Send,” is also to be used for navigating through an automated customer service center menu structure, and to leave a number on a pager. You can also send stored Uconnect Phonebook entries as tones for fast and easy access to voice mail and pager entries. To use this feature, dial the number you wish to call and then push the Voice Command button and say, “Send.” The system will prompt you to enter the name or number and say the name of the phonebook entry you wish to send. The Uconnect Phone will then send the corresponding phone number associated with the phonebook entry, as tones over the phone.
NOTE:
• You may not hear all of the tones due to mobile phone network configurations. This is normal. • Some paging and voice mail systems have system time out settings that are too short and may not allow the use of this feature.
Barge In – Overriding Prompts
The “Voice Command” button can be used when you wish to skip part of a prompt and issue your voice command immediately. For example, if a prompt is asking “Would you like to pair a phone, clear a...,” you could push the Voice Command button and say, “Pair a Phone” to select that option without having to listen to the rest of the voice prompt.
Turning Confirmation Prompts On/Off
Turning confirmation prompts off will stop the system from confirming your choices (e.g., the Uconnect Phone will not repeat a phone number before you dial it). To turn confirmation prompts on or off using Voice Com- mand: 1. Push the Phone button to begin. 2. After the “Ready” prompt and the following beep, say:
• “Setup Confirmations Prompts On” • “Setup Confirmations Prompts Off”
Phone And Network Status Indicators
If available on the radio and/or on a premium display such as the instrument panel cluster, and supported by your mobile phone, the Uconnect Phone will provide notifica- tion to inform you of your phone and network status when you are attempting to make a phone call using Uconnect Phone. The status is given for roaming, network signal strength, phone battery strength, etc.
Dialing Using The Mobile Phone Keypad
You can dial a phone number with your mobile phone keypad and still use the Uconnect Phone (while dialing via the mobile phone keypad, the user must exercise caution and take precautionary safety measures). By dialing a number with your paired Bluetooth mobile phone, the audio will be played through your vehicles audio system. The Uconnect Phone will work the same as if you dial the number using Voice Command.
NOTE: Certain brands of mobile phones do not send the dial ring to the Uconnect Phone to play it on the vehicle audio system, so you will not hear it. Under this situation, after successfully dialing a number the user may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio.
Mute/Un-Mute (Mute ON/OFF)
When you mute the Uconnect Phone, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you. To mute the Uconnect Phone: • Push the Voice Command button. • Following the beep, say “Mute.” To un-mute the Uconnect Phone: • Push the Voice Command button. • Following the beep, say “Mute off.”
Advanced Phone Connectivity Transfer Call To And From Mobile Phone
The Uconnect Phone allows ongoing calls to be transferred from your mobile phone to the Uconnect Phone without terminating the call. To transfer an ongoing call from your Uconnect Phone paired mobile phone to the Uconnect Phone or vice versa, push the Voice Command button and say “Transfer Call.”
Connect Or Disconnect Link Between The Uconnect Phone And Mobile Phone
Your mobile phone can be paired with many different electronic devices, but can only be actively connected with one electronic device at a time. If you would like to connect or disconnect the Bluetooth connection between a Uconnect Phone paired mobile phone and the Uconnect Phone, follow the instructions described in your mobile phone user manual.
List Paired Mobile Phone Names
• Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Setup Phone Pairing.”
• When prompted, say “List Phones.” • The Uconnect Phone will play the phone names of all paired mobile phones in order from the highest to the lowest priority. To “Select” or “Delete” a paired phone being announced, push the Voice Command button and say “Select” or “Delete.” Also, see the next two sections for an alternate way to “Select” or “Delete” a paired phone.
Select Another Mobile Phone
This feature allows you to select and start using another phone paired with the Uconnect Phone. • Push the Phone button to begin. • After the “Ready” prompt and the following beep, say “Setup Select Phone” and follow the prompts. • You can also push the Voice Command button at any time while the list is being played, and then choose the phone that you wish to select.
• The selected phone will be used for the next phone call. If the selected phone is not available, the Uconnect Phone will return to using the highest priority phone present in or near (approximately within 30 ft (9 m) the vehicle.
Delete Uconnect Phone Paired Mobile Phones
• Push the Phone button to begin.
• After the “Ready” prompt and the following beep, say “Setup Phone Pairing.”
• At the next prompt, say “Delete” and follow the prompts.
• You can also push the Voice Command button at any time while the list is being played, and then choose the phone you wish to delete.
Things You Should Know About Your Uconnect Phone Uconnect Phone Tutorial
To hear a brief tutorial of the system features, push the Phone button and say “Uconnect Tutorial.”
Voice Training
For users experiencing difficulty with the system recogniz- ing their voice commands or numbers, the Uconnect Phone Voice Training feature may be used. To enter this training mode, follow one of the two following procedures:
• From outside the Uconnect Phone mode (e.g., from radio mode), push and hold the Voice Command button for five seconds until the session begins, or,
• Push the Voice Command button and say the “Voice Training,” “System Training,” or “Start Voice Train- ing” command.
You can either push the Uconnect Phone button to restore the factory setting or repeat the words and phrases when prompted by the Uconnect Phone. For best results, the Voice Training session should be completed when the vehicle is parked with the engine running, all windows closed, and the blower fan switched off. This procedure may be repeated with a new user. The system will adapt to the last trained voice only. Reset To Reset all settings using Voice Command:
1. Push the Phone button.
2. After the “Ready” prompt and the following beep, say “Setup,” then “Reset.”
• This will delete all phone pairing, phone book entries,
and other settings in all language modes. The System will prompt you before resetting to factory settings.
Voice Command
For best performance:
• Adjust the rearview mirror to provide at least ½ inch (1 cm) gap between the overhead console (if equipped) and the mirror.
• Always wait for the beep before speaking.
• Speak normally without pausing, just as you would speak to a person sitting a few feet/meters away from you.
• Make sure that no one other than you is speaking during a Voice Command period.
Performance is maximized under:
• Low-to-medium blower setting • Low-to-medium vehicle speed • Low road noise • Smooth road surface • Fully closed windows • Dry weather condition
NOTE:
• Even though the system is designed for users speaking in North American English, French, and Spanish accents, the system may not always work for some.
• When navigating through an automated system such as voice mail, or when sending a page, at the end of speaking the digit string, make sure to say “Send.”
• Storing names in the phonebook when the vehicle is not in motion is recommended.
• It is not recommended to store similar sounding names in the Uconnect Phonebook.
• Phonebook (Downloaded and Uconnect Phone Local) name recognition rate is optimized when the entries are not similar.
• Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred.”
• You can say “O” (letter “O”) for “0” (zero). • Even though international dialing for most number combinations is supported, some shortcut dialing num- ber combinations may not be supported.
Far End Audio Performance
Audio quality is maximized under: • Low-to-medium blower setting • Low-to-medium vehicle speed • Low road noise • Smooth road surface • Fully closed windows • Dry weather conditions • Operation from the driver’s seat • Performance, such as audio clarity, echo, and loudness to a large degree rely on the phone and network, and not the Uconnect Phone
• Echo at the phone far end can sometimes be reduced by lowering the in-vehicle audio volume
Recent Calls
If your phone supports “Automatic Phonebook Down- load,” Uconnect Phone can list your Outgoing, Incoming and Missed Calls.
Voice Text Reply
Uconnect Phone can read or send new messages on your phone.
Read Messages:
If you receive a new text message while your phone is connected to Uconnect Phone, an announcement will be made to notify you that you have a new text message. If you wish to hear the new message: • Push the Phone button. • After the “Ready” prompt and the following beep, say
“SMS Read” or “Read Messages.” • Uconnect Phone will play the new text message for you. After reading a message, you can “Reply” or “Forward” the message using Uconnect Phone.
Send Messages:
You can send messages using Uconnect Phone. To send a new message: • Push the Phone button. • After the “Ready” prompt and the following beep, say “SMS Send” or “Send Messages.”
• You can either say the message you wish to send or say “List Messages.” There are 20 preset messages.
To send a message, push the Voice Command button while the system is listing the message and say “Send.” Uconnect Phone will prompt you to say the name or number of the person you wish to send the message to. List of Preset Messages:
1. Yes
2. No
3. Where are you?
4. I need more direction
5. L O L
6. Why
7. I love you
8. Call me
9. Call me later
10. Thanks
11. See you in 15 minutes
12. I am on my way
13. I’ll be late
14. Are you there yet?
15. Where are we meeting?
16. Can this wait?
17. Bye for now
18. When can we meet?
19. Send number to call
20. Start without me
Turn SMS Incoming Announcement ON/OFF
Turning the SMS Incoming Announcement OFF will stop the system from announcing the new incoming messages.
• Push the Phone button. • After the “Ready” prompt and the following beep, say “Setup, Incoming Message Announcement,” you will then be given a choice to change it.
Bluetooth Communication Link
Mobile phones have been found to lose connection to the Uconnect Phone. When this happens, the connection can generally be reestablished by switching the phone off/on. Your mobile phone is recommended to remain in Bluetooth ON mode.
Power-Up
After switching the ignition key from OFF to either the ON or ACC position, or after a language change, you must wait at least 15 seconds prior to using the system.
Voice Commands
Primary Alternate (s)
zero
one
two
three
four
five
six
seven
eight
nine
star (*)
plus (+)
pound (#)
add location
all
call
cancel
confirmation prompts
continue
Primary Alternate (s)
delete
dial
download
edit
emergency
English
erase all
Espanol
Francais
help
home
language
list names
list phones
mobile
mute
mute off
new entry
no
other
Primary Alternate (s)
pair a phone
phone pairing pairing
phonebook phone book
previous
record again
redial
return to main menu return or main menu
select phone select
send
set up phone settings or phone set up
towing assistance
transfer call
Uconnect Tutorial
voice training
work
yes
General Information
The following regulatory statement applies to all radio frequency (RF) devices equipped in this vehicle: This
device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Opera- tion is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Download Manual