2021 Ford Ranger Owners Manual - Keys and Remote Controls

Keys and Remote Controls

This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

The typical operating range for your transmitter is approximately 33 ft (10 m). Vehicles with the remote start feature will have a greater range.

One of the following could cause a decrease in operating range:

Weather conditions.

Nearby radio towers.

Structures around the vehicle.

Other vehicles parked next to your vehicle.

The radio frequency used by your remote control can also be used by other radio transmitters, for example amateur radios, medical equipment, wireless headphones, wireless remote controls, cell phones, battery chargers and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key.

Note: Make sure to lock your vehicle before leaving it unattended.

Note: If you are in range, the remote control will operate if you press any button unintentionally.

Note: The remote control contains sensitive electrical components. Exposure to moisture or impact may cause permanent damage.

The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met:

You activate the front exterior door handle switch.

You press the luggage compartment button.

You press a button on the transmitter.

If excessive radio frequency interference is present in the area or if the transmitter battery is low, you may need to mechanically unlock your door. You can use the mechanical key blade in your intelligent access key to open the driver door in this situation. See Remote Control (page 51).

Integrated Keyhead Transmitter(If Equipped)

Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control.

51

E277016

Press the button to release the key blade. Press and hold the button to fold the key blade back in when not in use.

E151795

Note: Your vehicle keys came with a security label that provides important key cut information. Keep the label in a safe place for future reference.

Note: You may not be able to shift out of park (P) unless the intelligent access key is inside your vehicle.

The remote control operates the power locks. The remote control must be in your vehicle to use the push button start.

The remote control also contains a removable key blade that you can use to unlock your vehicle.

52

A message appears in the information display when the remote control battery is low. See General Information (page 96).

The remote control uses one coin-type three-volt lithium battery.

Press the button to release the key blade before beginning the procedure.

Press the release button and pull the key blade out.

Insert a suitable tool, for example a screwdriver, in the position shown and gently push the clip.

Press the clip down to release the battery cover.

E151795

Note: Your vehicle keys came with a security label that provides important key cut information. Keep the label in a safe place for future reference.

Note: Refer to local regulations when disposing of remote control batteries.

Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.

Note: Replacing the battery does not erase the programmed key from your vehicle. The remote control should operate normally.

Carefully remove the cover.

53

E151800

Note: Do not touch the battery contacts or the printed circuit board with the screwdriver.

Insert a screwdriver as shown to release the battery.

1. Push the release button and pull the key blade out.

E151801

Remove the battery.

Install a new battery with the + facing up.

Replace the battery cover.

The remote control uses one coin-type three-volt lithium battery.

54

Twist a thin coin under the tab hidden behind the key blade head to remove the battery cover.

E218402

Insert a suitable tool, for example a screwdriver, in the position shown and carefully remove the battery.

Install a new battery with the + facing upward.

Reinstall the battery housing cover onto the remote control and install the key blade.

Press the button twice within three seconds. The horn sounds and the direction indicators

flash.

Note: The panic alarm only operates when the ignition is off.

Press the button to activate the alarm. Press the button again or switch the ignition on to

deactivate.

55

Remote Start (If Equipped)

Note: Do not use remote start if your fuel level is low.

The remote start button is on the remote control.

This feature allows you to start your vehicle from the outside. The remote control has an extended operating range.

If your vehicle has automatic climate control, you can configure it to operate when you remote start your vehicle. See Climate Control (page 117). A manual climate control system will run at the setting it was set to when you switched your vehicle off.

Many states and provinces have restrictions for the use of remote start. Check your local and state or provincial laws for specific requirements regarding remote start systems.

The remote start system does not work if:

The ignition is on.

The alarm system triggers.

You disable the feature.

The hood is open.

The transmission is not in park (P).

The vehicle battery voltage is too low.

The service engine soon light is on.

An LED on the remote control provides status feedback of remote start or stop commands.

Note: You must press each button within three seconds of each other. If you do not follow this sequence, your vehicle does not start remotely, the direction indicators do not flash twice and the horn does not sound.

E138626

To remote start your vehicle:

Press the lock button to lock all the doors.

Press the remote start button twice. The exterior lamps flash twice.

The horn sounds if the system fails to start.

Note: You must press the push button ignition switch on the instrument panel once while applying the brake pedal before driving your vehicle.

56

The power windows do not work during remote start and the radio does not turn on automatically.

The parking lamps remain on and your vehicle will run for 5, 10 or 15 minutes, depending on the setting.

To extend the engine running time duration of your vehicle during remote start, repeat steps 1 and 2 while the engine is running. If the duration is set to 15 minutes, the duration extends by another 15 minutes. For example, if your vehicle had been running from the first remote start for 10 minutes, your vehicle continues to run now for a total of 30 minutes. You can extend the engine running time duration to a maximum of 30 minutes.

Wait at least five seconds before remote starting after the engine stops running.

Press the button once. Your vehicle and the parking lamps turn off.

You may have to be closer to your vehicle than when starting due to ground reflection and the added noise of your running vehicle.

You can switch this feature on or off in the information display.

Replacement keys or remote controls can be purchased from an authorized dealer. Authorized dealers can program remote controls for your vehicle.

PASSIVE KEY BACKUP POSITION (IF EQUIPPED)

Place the passive key in the position shown, with the buttons facing upward. Make sure that you place the key fob in the center of the cup holder.

The top or bottom end of the key must be pointing towards the front or rear of the vehicle.

With the key in this position, press the brake or clutch pedal, then press the start button to switch on your vehicle.

57