Lighting
E242675
Slightly pull the lever toward you and release it to flash the headlamps.
|
|
WARNING: The system does not relieve you of your responsibility to drive with due care and attention. You may need to override the system if it does not turn the headlamps on in low visibility conditions, for example daytime fog.The headlamps remain on for a period of time after you switch the ignition off. Use the information display controls to adjust the period of time that the headlamps remain on.
Note: If you switch the autolamps on, you cannot switch the high beams on until the system turns the low beams on.
When you switch the autolamps on, the headlamps turn on within 10 seconds of switching the wipers on. They turn off approximately 60 seconds after you switch the windshield wipers off.
The headlamps do not turn on with the wipers:
Note: If you switch the autolamps and the autowipers on, the headlamps turn on when the windshield wipers continuously operate.
Note: When disconnecting the battery or when it runs out of charge, the illuminated components turn to the maximum setting.
E142451
When the lighting control is in the autolamps position, the headlamps turn on in low light situations, or when the wipers turn on.
72
E231828
Press repeatedly or press and hold until you reach the desired level.
E165366
|
|
WARNING: The daytime running lamps system does not activate the rear lamps and may not provide adequate lighting during low visibility driving conditions. Make sure you switch the headlamps on, as appropriate, during all low visibility conditions. Failure to do so may result in a crash.The daytime running lamps turn on when:
1. Switching the ignition on.
2. The transmission is not in park (P) for vehicles with automatic transmissions, or releasing the parking brake for vehicles with manual transmissions.
3. The lighting control is in the off, parking lamp or autolamps positions.
4. The headlamps are off.
Switch the daytime running lamps on or off using the information display. See Information Displays (page 90).
The daytime running lamps turn on when:
The other lighting control switch positions do not turn on the daytime running lamps.
73
If the daytime running lamps are off in the information display, the lamps stay off in all switch positions.
AUTOMATIC HIGH BEAM CONTROL (IF EQUIPPED)
|
|
WARNING: The system does not relieve you of your responsibility to drive with due care and attention. You may need to override the system if it does not turn the high beams on or off.The system turns on high beams if it is dark enough and no other traffic is present. If it detects an approaching vehicle’s headlamps or tail lamps, or street lighting ahead, the system turns off high beams before they can distract other road users. Low beams remain on.
Note: The system may not operate properly if the sensor is blocked. Keep the windshield free from obstruction or damage.
Note: The system may not operate properly in cold or inclement conditions. You can switch on the high beams by overriding the system.
Note: If the system detects a blockage, for example bird droppings, bug splatter, snow or ice, the system goes into low beam mode until you clear the blockage. A message may appear in the information display if the camera is blocked.
Note: Using much larger tires or equipping vehicle accessories such as snowplows can modify your vehicle's ride height and degrade automatic high beam control performance.
A camera sensor, centrally mounted behind the windshield of your vehicle, continuously monitors conditions to turn the high beams on and off.
Once the system is active, the high beams turn on if:
The system turns the high beams off if:
Switch the system on using the information display. See Information Displays (page 90).
E142451
Switch the lighting control to the autolamps position. See Autolamps (page 72).
Push the lever away from you to switch between high beam and low beam.
74
The indicator illuminates to confirm when the system is ready to assist.
Push the lever up or down to switch the direction indicators on.
Note: Tap the lever up or down to make the direction indicators flash three times.
Set the lever to the middle position to switch the direction indicators off.
Flashes when you switch the direction indicators on.
Note: An increase in the rate of flashing warns of a failed indicator bulb.
E142453
Press the control to switch the fog lamps on or off.
You can switch the fog lamps on when the lighting control is in any position except Off and the high beams are not on.
E249790
A B C
Switch all lamps on.
Switch lamps on and off by door. Switch all lamps off.
E242676
If you set the switch to the door position, the courtesy lamp illuminates when you unlock or open any door. If you leave a door open with the ignition switched off, the courtesy lamp goes off after some time to prevent your vehicle battery from losing charge. To switch it back on, switch the ignition on for a short time.
The courtesy lamp also illuminates when you switch the ignition off. It goes off after a short time or when you start the engine.
75
If you set the switch to the all on position with the ignition switched off, the courtesy lamp illuminates. It goes off after a short time to prevent your vehicle battery from losing charge. To switch it back on, switch the ignition on for a short time.
E249791
Press the edge of the lamp lens to switch on and off.
If you switch the ignition off, the reading lamps turn off after a short time.
Note: This is to prevent the vehicle battery from losing charge.
E250958
For rear lamps without a position switch, press the lamp lens to switch on and off.
Use the touchscreen to select the following:
Select the settings option on the feature bar.
Select ambient lighting.
E273192
Touch a color once.
Touch any color once.
Drag the selected color up or down.
Touch the selected color once or drag the selected color down to zero brightness.
Press the button on the lighting control to switch on the lamps.
Note: The lamps turn off when you reach 3 mph (5 km/h).
Note: The cargo lamps gradually turn off after a period of time.
76
Download Manual