Opening and closing
~ If the vehicle key that was used most recently is inside the luggage compartment, the luggage compartment lid will automatically open again after it closes >@.
~ If the vehicle key that was last used is detected inside the vehicle, then the vehicle cannot be locked from the outside >.
Observe the safety precautions > page 34.
Applies to: vehicles with power closing ~To reduce the risk of injury, make sure that
the area where the door is closing is clear during the closing process.
~The closing process can be stopped at any time by pulling on the outer or inner door handle.
The following applies when locking the vehicle: = If the vehicle key that was last used is detected inside the passenger compartment, then the vehicle cannot be locked from the outside using the sensor. Take the vehicle key with you and lock the vehicle again. Otherwise, the vehicle will not be protected against unauthorized access.
— Applies to: vehicles with convenience key: you try to lock the vehicle using the button ‘on the vehicle key while the front passenger’s or rear door is open, and you accidentally place the vehicle key inside the passenger compartment and close the door, the vehicle will lock at first. But if the keyless system detects a vehicle key inside the vehicle after it locks, then the vehicle will unlock again. The turn signals will flash several times and a warning tone” will sound to indicate this. If you do not open the vehicle to remove the vehicle key within a brief period, then the vehicle will lock automatically. This prevents the vehicle from being left un1) Applies to: vehicles with anti-theft alarm system
locked for long periods of time. The vehicle key will then be locked inside the vehicle.
— Applies to: vehicles with convenience key: If the luggage compartment lid closes and the system detects that the last vehicle key that was used is inside the luggage compartment, then the luggage compartment lid will open again. The turn signals will flash several times and a warning tone” will sound to indicate this. The doors will lock. Always take the vehicle key with you, or unauthorized persons may be able to enter the vehicle.
—Do not leave valuables unattended in the vehicle. A locked vehicle is not a safe!
~The LED in the driver's door rail blinks when you lock the vehicle. If the LED turns on for approximately 30 seconds after locking, there is a malfunction in the central locking system. Have the problem corrected by an authorized Audi dealer or authorized Audi Service Facility.
Setting the central locking system You can adjust the central locking system to your preferences. The settings depend on the vehicle equipment. > Applies to MMI: Select on the home screen: VE~ HICLE > Settings & Service > Central locking.
Door unlocking ~ If you select All, all doors and the luggage compartment lid will be unlocked when unlocking the vehicle.
~ If you select Driver's door, only the driver's door will be unlocked. To unlock all doors and the luggage compartment lid, press the @ button on the vehicle key twice. In vehicles with a convenience key*, only the driver's door will unlock when you pull the driver's door handle. If, you pull another door handle, the entire vehicle will be unlocked.
Opening and closing
The entire vehicle will always be locked f you press the @ button.
Long press to open windows You can select if all windows and the panoramic glass roof* should open using the vehicle key page 46, Convenience opening and closing. If you press and hold the f button on the vehicle key, all of the windows and the panoramic glass roof* will close. Disable rear lid handle You can select if the luggage compartment lid can open with the handle > page 42, fig. 26. If you activate this function, the luggage compartment lid can only be opened with the 4S button on the vehicle key or in the driver's door. In vehicles with a convenience key’, you can still open the luggage compartment lid using the handle if an authorized convenience key is detected > page 41. Fold mirrors You can select if the exterior mirrors automatically fold in when locking. Tone when locking” You can select if an audio signal sounds when locking the vehicle. Open with convenience key Applies to: vehicles with convenience key You can deactivate the feature for unlocking using the sensor. The function for locking via the sensor will still be enabled page 40.
1) This function is not available in all countries.
Central locking switch
Fig. 20 Driver's door: central locking switch
» To lock or unlock the vehicle, press the or 3 button > A\.
When locking the vehicle with the central locking switch, the following applies:
~The doors and the luggage compartment lid cannot be opened from the outside for security reasons, for example, to reduce the risk of unauthorized entry while stopped at a light.
~The LED in the central locking switch turns on when all doors are closed and locked.
~You can open the doors individually from the inside by pulling the door handle one time. To open the rear doors individually, you must pull the door handle twice.
~In the event of a crash with airbag deployment, the doors unlock automatically to allow access to the vehicle.
— Observe the safety precautions > page 34. ~The central locking button works when the
ignition is switched off. ~The central locking switch is inoperative when the vehicle is locked from the outside.
Messages The following messages may appear depending on the vehicle equipment: BB priver's door: malfunction! Shift to P before leaving vehicle. See owner's manual >
Opening and closing
There is a malfunction in the driver's door. Secure the vehicle before exiting by selecting the “P” selector lever position. Drive immediately to an authorized Audi dealer or authorized Audi Service Facility to have the malfunction repaired.
Ei central locking: malfunction! See owner's manual There is a central locking malfunction. If the doors cannot lock, you can emergency lock the doors page 37. Drive to an authorized Audi dealer or authorized Audi Service Facility immediately to have the malfunction corrected.
EB Door lock: opening while driving is only possible with the emergency release. See owner's manual It is not possible to power unlock the doors at speeds above approximately 9 mph (15 km/h). If you must open doors at higher speeds in cases of emergency, you can manually unlock the door by forcefully pulling the door handle beyond its noticeable resistance two times. Then press the door handle back into its original position, if necessary.
Mechanically unlocking and locking the doors
All doors must be unlocked or locked separately if the central locking system fails.
Fig. 21 Driver's door: door lock cylinder
Fig. 22 Door: mechanically locking
Applies to: vehicles with anti-theft alarm system: After unlocking using the lock cylinder and opening the driver's door, you must press the @ button on the vehicle key or switch the ignition on. Otherwise the alarm will sound. Unlocking or locking the driver's door with the mechanical key
» Remove the mechanical key page 39.
» Insert the mechanical key into the slot under
the door handle and pry the cap off fig. 27. > To unlock the driver's door, turn the mechanical
key to the unlock position in the direction of arrow @) > fig. 27.
» Pull the door handle to open the driver's door.
» To lock the driver's door, select the "P" selector
lever position, close the door, and turn the key once to the close position @=> A\.
Locking the front passenger's door and rear doors using the mechanical key The mechanical lock is located on the edge of the door @) or in the latch opening @) fig. 22. Itis only visible when the door is open.
» Remove the mechanical key page 39.
» If necessary, remove the cap from the opening fig. 22.
Opening and closing
» Insert the mechanical key into the slot on the inside and turn it all the way to the right (right door) or left (left door).
» If necessary, install the cap in the opening and close the door.
Once the front passenger's door or rear doors close, it will no longer be possible to open them from the outside. The front doors can be opened from the inside by pulling the door handle one time. The rear doors can be unlocked from the inside by pulling the door handle one time and then opened by pulling the door handle again. If the child safety lock in one of the rear doors is activated, you must first pull the door handle from the inside. Then you can open the door from the outside.
Observe the safety precautions > page 34.
Anti-theft alarm system ‘Applies to: vehicles with anti-theft alarm system If the anti-theft alarm system detects a vehicle break-in, audio and visual warning signals are triggered. The anti-theft alarm system is switched on or off when locking or unlocking your vehicle. If the alarm is triggered, it will shut off automatically after a certain amount of time. Switching the alarm off manually > To switch the alarm off, press the G button on
the vehicle key or switch the ignition on. Depending on the vehicle equipment, the antitheft alarm system may have the following features:
Break-in security feature The alarm will be triggered if the doors, the hood, or the luggage compartment lid are broken into, or if a door that was previous unlocked using the lock cylinder is opened. Interior/towing protection monitor The alarm will be triggered if there are movements detected in the vehicle interior (for example, by animals) or if there is a change in the vehi38
cle angle (for example, when the vehicle is being towed). You can prevent the alarm from being triggered by deactivating the interior/towing protection monitor. Deactivating the interior/towing protection monitor There are the following options for deactivating the interior/towing protection monitor:
» Press the &@ button on the vehicle key a second
time iin two seconds. Or
» Applies to: vehicles with convenience key: Touch the sensor on the door handle a second time within two seconds. Or
» Turn the mechanical key in the door lock to the close position a second time within two seconds. Or
> Applies to: vehicles with MMI: Select on the home screen: VEHICLE > Settings & Service > Interior monitoring.
If you lock the vehicle, then the interior/towing protection monitor will stay off until the next time the vehicle is unlocked.
No one, especially children, should stay in the vehicle when it is locked from the outside, because the windows can no longer be opened from the inside. Locked doors make it more difficult for emergency workers to enter the vehicle, which puts lives at risk.
The interior/towing protection monitor only functions correctly when the windows and the panorama glass roof* are closed.
Opening and closing
Fig. 23 Your vehicle key set
The key set includes two vehicle keys when delivered from the factory. @ Vehicle key You can unlock and lock your vehicle with the vehicle key. @ Mechanical key and release button for mechanical key A mechanical key is integrated in the vehicle key. To remove it, press the release button and remove the mechanical key. Using the mechanical key, you can: — Lock or unlock the glove compartment. ~ Manually unlock and lock the doors page 37. ~ Unlock the luggage compartment lid using the emergency release > page 45.
@ PANIC button In an emergency, you can press the PANIC button to trigger a visible and audible vehicle alarm. You can do this ass long as you are near your vehicle (within the range for the remote control key).
—To trigger the alarm, press the fig. 23.
To turn the alarm off, press thi again.
Lost key/replacing a key If a vehicle key is lost, contact an authorized Audi dealer or autho ized Audi Service Facility. Have this vehicle key deactivated. It is important to bring all keys with you.
Ifa key is lost, you should report it to your insurance company. Electronic immobilizer
The immobilizer prevents unauthorized use of the vehicle.
In some cases, it may not be possible to establish vehicle drive ready mode if there is also a vehicle key from a different vehicle manufacturer on the key chain. Data in the vehicle key When driving, service and maintenance-relevant. data is continuously stored in your vehicle key. An authorized Audi dealer or authorized Audi Service Facility can read out this data and tell you about the work your vehicle needs.
Observe the safety precautions > page 34.
Protect the key against high temperatures and direct sunlight.
OH Batteries and electrical/electronic devices must be disposed of in an environmentally safe manner.
~The vehicle key function can be temporarily disrupted by interference from transmitters near the vehicle working in the same frequency range (such as a mobile device or radio equipment). Always check if your vehicle is locked.
— Applies to MMI: You can view the number of keys programmed to the vehicle by selecting on the home screen: VEHICLE > Settings & Service > Vehicle information.
~Akey tag that contains information about the vehicle key set may be attached to the key set at the factory. The key tag can be used to reorder vehicle keys. Keep the key tag. If you sell the vehicle, give the key tag to the buyer.
Opening and closing
~The system complies with United States FCC regulations and ISED regulations = page 320.
Unlocking and locking the vehicle
Fig. 24 Door handle: sensor for locking
Depending on the vehicle equipment, you may have various options for unlocking and locking your vehicle. The settings in the MMI specify which doors will unlock page 35. Unlocking or locking using the vehicle key buttons
» To unlock the vehicle, press the & button
page 39, fig. 23.
» To lock the vehicle, press the & button once.
Unlocking or locking using the sensors Applies to: vehicles with convenience key
» To unlock a door or the luggage compartment
lid, grasp the door handle or luggage compartment lid handle.
» To lock the vehicle, close the door and touch the sensor on the door handle once fig. 24. Do not grasp the door handle while locking the vehicle, or else the vehicle will not lock. The door cannot be opened for a brief period directly after locking it. This way you have the opportunity to check if the doors locked correctly.
Unlocking and locking with the Audi connect vehicle control service! Applies to: vehicles with Audi connect vehicle control Requirement: Audi connect vehicle control services must be set up * page 200. The vehicle must be parking and the ignition must be switched off.
1 Incertain countries.
Observe the safety precautions > page 34.
— Only use the vehicle key when you can see the vehicle.
~The vehicle can only be locked when the "P” selector lever position is engaged.
— Do not use the vehicle key to lock and unlock when you are inside the vehicle. Otherwise, you could trigger the anti-theft alarm*. If this happens, press the @ unlock button.
Applies to: vehicles with convenience key —When unlocking or locking the vehicle, the convenience key cannot be more than approximately 4 feet (1.5 m) away from the door handle or luggage compartment.
~ Unlocking with the convenience key (keyless access) can be deactivated in the MMI system page 35.
~To prevent the vehicle battery from discharging, the energy management gradually switches off convenience functions that are not needed. You then may no longer be able to unlock your vehicle with the sensors.
LED and batter the vehicle key
Fig. 25 Vehicle key: removing the battery holder
LED in the vehicle key The LED @ indicates the vehicle key function. = >
Opening and closing
» If you press a button briefly, the LED blinks once.
» If you press and hold a button (convenience opening/closing), the LED blinks several times.
» If the LED does not blink, the vehicle key battery is drained. Replace the battery in the vehicle key.
Replacing the vehicle key battery The replacement battery in the remote control key must meet the same specifications as the original battery (battery type CR 2032).
» Remove the mechanical key @ page 39 and insert it at an angle into the opening fig. 25.
» Push the mechanical key in the opening in the direction of the arrow to operate the release button on the inside @). To reduce the risk of damage, do not try to pry off the cover.
» Remove the cover from the battery tray.
» Insert the new battery with the “+” symbol facing up.
» Close the battery tray with the cover.
» Insert the mechanical key. If the fim indicator light appears with a corresponding message, the vehicle key battery is drained and must be replaced
If batteries or coin cell batteries are swallowed or enter the body in any other way, they can cause serious or fatal injuries within a short period of time. There is a risk of chemical burns. — Keep vehicle keys and key fobs with batteries out of the reach of children. — Keep new or used batteries away from children. — If the battery compartment on a vehicle key does not close securely, stop using the key and keep it away from children.
= Seek medical attention immediately if you suspect that a battery was swallowed or has entered the body in any other way.
Of Batteries and electrical/electronic devices must be disposed of in an environmentally safe manner.
Luggage compartment lid General information
— Applies to: vehicles with anti-theft alarm. system: When the vehicle is locked from the outside, no one, especially children, should remain in the vehicle, because the windows can no longer open from the inside <page 38. Locked doors make it more difficult for emergency workers to enter the vehicle, which puts lives at risk.
— Always close and lock the luggage compartment lid and the doors when the vehicle is not in use. Otherwise someone such as a child could enter the vehicle through the luggage compartment and become locked inside it. To reduce the risk of injury, do not allow children to play in or around the vehicle.
=To reduce the risk of injuries by pinching, make sure that no one is in the operating area of the luggage compartment lid when closing, especially near the hinges, at the upper and lower edges of the lid, or all around the edge of the lid in general.
— After closing the luggage compartment lid, make sure that itis latched. The luggage compartment lid could open suddenly while driving, which would increase the risk of an accident.
— Never drive with the luggage compartment lid ajar or open, because poisonous gases from the surrounding area can enter the vehicle interior and increase the risk of asphyxiation.
= If there is a luggage rack (such asa bicycle rack) on the luggage compartment lid, the luggage compartment lid may not open completely under certain circumstances or it
Opening and closing
could close by itself if open due to the extra weight. Therefore, the open luggage compartment lid must be given additional support or the cargo must first be removed from the luggage rack.
— Applies to: vehicles with power-operated or sensor-controlled luggage compartment lid: Pay careful attention when closing the luggage compartment lid. Otherwise, you could cause serious injury to yourself or others despite the pinch protection.
The luggage compartment lid can bump into objects such as the garage ceiling when opening and become damaged.
—When the vehicle is locked, the luggage compartment lid can be unlocked separately by pressing the Zs button twice on the vehicle key. The luggage compartment lid locks automatically when itis closed again.
~The ability to open the luggage compartment lid using the handle > page 42, fig. 26 can be deactivated or activated in the MMI page 35.
Opening and closing the luggage compartment lid
Fig. 26 Rear lid: handle
Fig. 27 Driver's door: opening the luggage compartment lid
Opening the luggage compartment lid
» Unlock the vehicle or the luggage compartment
lid using the 3 / As button on the vehicle key and press the handle in the luggage compartment lid fig. 26. Or
» Applies to: vehicles with convenience key:Press the handle in the luggage compartment lid fig. 26. When the luggage compartment is locked, the vehicle key cannot be more than approximately 4 feet (1.5 m) away from the luggage compartment. Or
> Applies to: vehicles with automatic luggage compartment lid: Select the "P" selector lever position and pull the <s fig. 27 button in the driver's door.
Closing the luggage compartment lid > See page 43, Automatic luggage compartment lid.
Observe the safety precautions > page 41.
Opening and closing
Automatic luggage compartment
Applies to: vehicles with automatic luggage compartment lid
Fig. 28 Luggage compartment lid: @ closing button*, @ lock button* (vehicles with convenience key")
The luggage compartment lid can be opened and closed automatically > A\ in General information on page 41. Opening the luggage compartment lid > When the ignition is switched off, press the As button on the vehicle key twice > page 39, fig. 23. Or
» Engage the “P” selector lever position and pull the <3 button* in the driver's door. Or
> Applies to: vehicles with convenience key: Press the handle in the luggage compartment lid @) page 42, fig. 26. When the luggage compartment is locked, the vehicle key cannot be more than approximately 4 feet (1.5 m) away from the luggage compartment.
Closing the luggage compartment lid
» Press the <¥ button in the luggage compartment lid. Or
» Press the handle in the luggage compartment lid page 42, fig. 26. Or
» Press the luggage compartment lid downward slightly. Or
» When the ignition is switched on, pull the <¥ switch in the driver's door page 42, fig. 27 until the luggage compartment lid is closed. Or
» Applies to: vehicles with convenience key: Press and hold the 2s button on the vehicle key while the ignition is switched off until the luggage compartment lid closes. Make sure there is enough distance (maximum of approximately 9 feet (3 m)) between you and the luggage compartment lid. Or
» Press the << button in the luggage compartment lid. Or
» Applies to: vehicles with convenience key: When the ignition is switched off, press the </ button in the luggage compartment lid. The vehicle key must not be more than approximately 4 feet (1.5 m) away from the luggage compartment and it must not be inside the vehicle. If you press the (* button, then the vehicle will lock.
Stopping automatic opening or closing The automatic opening or closing of the luggage compartment lid will stop if:
» You press the << button or press the handle in the luggage compartment lid again > page 42, fig. 26. Or
> You press the 4s button on the convenience key*. Or
» Something blocks the luggage compartment lid or makes it difficult for the lid to move.
Ifyou press the button <3 or the handle in the luggage compartment lid 2 page 42, fig. 26 again, the luggage compartment lid will open or close again. Storing the luggage compartment lid opening position The position must be at a certain height or higher to store.
» Bring the luggage compartment lid into the desired open position. If you want to move the luggage compartment lid to a lower position, move it slowly in small increments; otherwise, the luggage compartment lid will close automatically.
» Press and hold the <3 button in the luggage compartment lid for at least four seconds to store the new opening position. A visual and audio signal will follow.
» To set a higher open position, wait at least five seconds and then carefully press the luggage compartment lid upward.
» Press and hold the <3 button again for at least four seconds to store the desired opening position.
Opening and closing
Manually opening and closing the luggage compartment lid If the electric motor malfunctions or the vehicle battery charge level is low, the luggage compartment lid can be opened or closed by hand. Extra force will be needed to do this. Move the lid slowly to reduce the amount of force needed.
» Pull the luggage compartment lid down slightly
by the inside handle* and then press on the lid until it latches.
Observe the safety precautions > page 417.
Opening and closing the luggage compartment lid with foot motion (kicking movement)
Applies to: vehicles with sensor-controlled luggage compartment lid
Fig. 29 Vehicle rear: foot motion (example)
The luggage compartment lid can be opened and closed automatically " > A\ in General information on page 41. Requirements: you must be carrying your convenience key* with you. The ignition must be switched off. You must be standing at the center behind the luggage compartment lid. Depending on vehicle equipment, it may also be possible to stand slightly off-center at the back of your vehicle. > Move your foot back and forth under the bumper one time fig. 29. Do not touch the bumper. Make sure you have firm footing. The luggage compartment lid will open or close ") once the
The closing function applies to vehicles that also have automatic luggage compartment lid operation
system detects the movement. The automatic opening or closing will be canceled if you repeat one of the movements described.
Observe the safety precautions > page 41.
Please note that when you have the convenience key with you, the sensor-controlled luggage compartment lid could open or close unexpectedly during activity near the rear of the vehicle. This increases the risk of an accident. Please note that when you have the convenience key with you, the sensor-controlled luggage compartment lid could open or close unexpectedly during activity near the rear of the vehicle (for example, the lid could hit the ceiling in a garage).
The luggage compartment lid will only open or close )) if you perform the movement as described. This prevents the luggage compartment lid from opening or closing due to similar movements ”), such as when you walk between the rear of the vehicle and your garage door. In some situations, the function may be limited or temporarily unavailable. This may happet — You are standing too close to the bumper or
too far away from it ~The luggage compartment lid was closed or opened immediately beforehand
— You park close to a hedge and the branches move back and forth under the vehicle for a long period of time
~ You clean your vehicle, for example with a pressure washer or in a car wash
~There is heavy rain The bumper is very dirty, for example after
driving on salt-covered roads
Opening and closing
= There is interference to the vehicle key's radio signal, such as from mobile devices or remote controls
Mechanically unlocking the luggage compartment lid The luggage compartment lid can be released from the inside in an emergency.
Fig. 30 Inner luggage compartment lid: access to the emergency release
» Fold the backrest on the rear bench seat forward page 91.
» Remove the mechanical key > page 39.
» Using the mechanical key, pry the cover &> off
the luggage compartment lid trim panel.
» Press the lever with the mechanical key in the
direction of the arrow to release the luggage compartment lid.
Observe the safety precautions > page 41.
Ifyou have folded the backrests into the upright position, always check if the lock is correctly engaged by pulling forward on the “backrest.
Child safety lock The child safety lock prevents the rear doors from being opened from the inside and the rear power windows from being operated.
Fig. 31 Driver's door: controls
» To activate or deactivate the child safety lock for the rear doors (which controls the power windows and interior door handle), press the left and/or right @ button in the driver's door
fig. 31. The LED in the button will turn on or off.
» Make sure the child safety lock is working by checking the function on the rear power window switch and door handle.
» Applies to: vehicles with controls for the climate control system in the rear and MMI: To also restrict the operation of the climate control system in the rear, select on the home screen: SETTINGS > Display & brightness > Operation in rear
When the child safety lock is switched on, the following functions are disabled:
~The rear inner door handles ~The rear power windows ~The control panel* for the climate control system in the rear
Message in the instrument cluster display The following messages may appear depending on the vehicle equipment: @®/ Child safety lock: malfunction! Please contact Service
There is a malfunction in the child safety lock. Press the button again.
Opening and closing
If the message stays on, drive immediately to an authorized Audi dealer or authorized Audi Service Facility to have the malfunction repaired.
— Observe the safety precautions > page 34. —A malfunction in the child safety lock could allow the rear doors to be opened from the inside, which increases the risk of an accident.
Power windows Opening and closing the windows
Fig. 32 Driver's door: power window switch
Power window switches: Left front door Right front door @ Left rear door @ Right rear door
Opening and closing the windows The driver can control all power windows. All power window switches are equipped with a twostage function:
» To open or close the window completely, press
the switch down or pull the switch up briefly to the second level. The operation will stop if the switch is pressed or pulled again.
» To select a position in between opened and closed, press or pull the switch to the first level until the desired window position is reached.
Correcting a malfunction in the one-touch up/down function If necessary, you can reactivate the one-touch up/ down function if it malfunctions.
» Pull the power window switch up until the window is completely raised.
» Release the switch and pull it up again for at least one second.
— Observe the safety precautions > page 34. — Never close the windows carelessly or in an
uncontrolled manner, because this increases the risk of injury.
—You can still open and close the windows for several minutes after turning the ignition off. The power window switch is not disabled until the driver's door or front passenger's door is opened.
~The power windows are equipped with pinch protection. The automatic window may stop closing and will open all the way again even if no obstacle is detected. Pull the power window switch up until the window is completely raised.
Convenience opening and clo Applies to: vehicles with convenience key
Convenience opening or closing the windows or panoramic glass roof* You can set in the MMI if all windows or the roof* should open or close all at once «> page 35, Setting the central locking system.
» Press and hold the @ or @ button on the vehicle key until all windows and the roof* have reached the desired position > /\. Or
> Touch the sensor* on the door handle > page 40, fig. 24 until all of the windows and the roof* are closed. Do not place your hand in the door handle when doing this.
When all of the windows and the roof* are closed, the turn signals will flash once.
— Observe the safety precautions > page 34. —Never close the windows or panoramic glass
roof* carelessly or in an uncontrolled
Opening and closing
manner, because this increases the risk of injury.
~ For security reasons, the windows and the panoramic glass roof* can only be opened and closed with the vehicle key at a maximum distance of approximately 6.5 feet (2 m) from the vehicle. Always pay attention when using the & button to close the windows and the panoramic glass roof* so that no one is pinched. The closing process will stop immediately when the & button is released.
Applies to: vehicles with panoramic glass roof: If the sunshade is closed, it will automatically open partially when the roof is tilted.
Panoramic glass roof Operating the panoramic glass roof and roof sunshade Applies to: vehicles with panoramic glass roof and roof sunshade
Fig. 33 Headliner: panoramic glass roof and sunshade” buttons
The control buttons are equipped with a twostage function. When tilting or opening the roof, the roof sunshade will open partially or completely if the sunshade is closed. Operating the roof sunshade The roof sunshade cannot be closed completely if the roof is open.
» Opening and closing the sunshade: push the #* switch in the headliner @) briefly forward or toward the rear to the second level.
» Partially opening the sunshade: press the switch to the first level until the sunshade reaches the desired position.
Operating the roof > Tilting the roof: press the > switch in the headliner briefly up to the second level @).
> Closing the tilted roof: pull the > switch down briefly to the second level.
> Applies when the sunshade is open: Opening the roof: push the <> button toward the rear briefly to the second level @.
> Closing the opened roof: push the > switch forward briefly to the second level.
> Applies when the sunshade is open: Opening partially: push, press, or pull the 2> switch to the first level until the roof reaches the desired position.
Quick opening You can also open the roof and roof sunshade in one movement.
» Push the 2 switch back briefly to the second level @ twice in a row.
If necessary, you can interrupt the quick opening or closing process by pressing the button aga Roof emergency closing If an object is detected when closing, the roof will open again automatically. In this case, you can then close it with the power emergency closing function.
> Within five seconds after the sunroof opens automatically, pull the applicable button until the roof is closed.
— Observe the safety precautions = page 34. ~To reduce the risk of injury, always pay attention when closing the roof. Always switch the ignition off and take the key with you when leaving the vehicle.
Opening and closing
Always close the roof when you leave the vehicle and when there is precipitation to reduce the risk of damage to the interior equipment, particularly the electronic equipment.
— After switching off the ignition, the roof and sunshades can still be operated for several minutes as long as neither of the front doors have been opened.
~ It is not possible to open the roof when temperatures are too low.
Garage door opener
Applies to: vehicles with garage door opener With the garage door opener, you can activate systems such as the garage doors, security systems or house lights from inside your vehicle. These functions are operated in the MMI. Multiple receivers can be programmed, which can control the functions of up to eight! hand-held transmitters.
—When operating or programming the garage door opener, make sure that no people or objects are in the area immediately surrounding the equipment. People can b jured or property can be damaged if struck when closing.
— Do not allow yourself to be distracted from traffic by the viewing and operating the displays.
= If you sell your vehicle, reset all settings to the factory default settings = page 238.
= The system complies with United States FCC regulations and ISED regulations page 320.
The possible number of hand-held transmitters depends on the equipment.
Before you program your system to the garage door opener, first check the compati ty: ~ Ask an authorized Audi dealer or authorized
Audi Service Facility or check at www. homelink.com. You can also find more information about HomeLink there.
~You can display information about HomeLink (compatibility level/status/country code/HomeLink generation) in the MMI:
~Select on the home screen: VEHICLE > Settings & Service > Garage door opener > @.
Applies to: vehicles with garage door opener
Requirements: the remote control transmitter must be programmed page 49, Programming, the vehicle must be within range of the system, and the ignition must be switched on.
There are multiple options to open or close the system (such as the garage door).
» If you have only programmed one remote control transmitter, press the -@ button on the lower display. Or
> Ifyou have programmed multiple remote control transmitters, press the 2 button on the lower display and then press the respective system button. Or
» Applies to: vehicles with programmable steering wheel button: If you have configured the programmable steering wheel button, press the >K button page 30. Or
» Applies to: vehicles with location pairing: If you have programmed Location pairing, press the button for this in the upper display (notification center page 22). As you approach the system, the button is displayed on the MMI.
If transmission was successful, the message: Send to: XXX will appear.
Opening and closing
Applies to: vehicles with garage door opener You can program both fixed code and rolling code systems in the MMI using the procedure that is described. Requirement: the ignition must be switched on.
Programming the system Applies to: MMI Requirement: the hand transmitter must be present and the vehicle must be within range of the system (such as the garage door) that you would like to program. > If you are programming the garage door opener
for the first time, press the ‘ button on the lower display. Follow the instructions in the upper display. Or
> If you would like to program other systems, select on the home screen: VEHICLE > Settings & Service > Garage door opener. Select the desired button: @). Follow the instructions in the MMI.
> If you would like to reprogram systems that are already programmed, select on the home screen: VEHICLE > Settings & Service > Garage door opener. Press the 4 button and select 7 for the system to be reprogrammed. Select: Program. Follow the instructions in the MMI.
With some systems, the garage door opener will be immediately available after programming. With other systems, the garage door opener must also be synchronized. Synchronizing” Requirement: the hand transmitter must already be programmed and the vehicle must be within range of the system (such as the garage door). If the system synchronization is performed directly after the programming procedure, follow the instructions on the MMI. If you would like to sync at a later time:
1 Only applies to rolling code systems
> Applies to: MMI: Select on the home screen: VEHICLE > Settings & Service > Garage door opener.
> Press the button for the system that you would like to synchronize.
» Follow the instructions in the MMI. Location pairing Applies to: vehicles with location pairing For easier operation, you can program your systems location.
Requirements: the respective hand transmitter must be programmed page 49 and the vehicle must be located in front of the system.
» Ifyou have programmed your system, follow the instructions in the MMI. Or
If you would like to set up location pairing at another time:
» Applies to: MMI: Select on the home screen: VEHICLE > Settings & Service > Garage door opener.
» Press the Z button. > Press the 7 button for the system your vehicle
is facing.
» Select: Location pairing. > Follow the instructions in the MMI. Only a maximum of three systems can be displayed in the notification center > page 22. If you would like to have all systems displayed, press oo 88. Renaming programmed systems You can rename the programmed systems according to your preferences (names may have a maximum of 10 characters).
» Ifyou have programmed your system, follow
the instructions in the MMI. Or
If you would like to change the name at another tim
» Applies to: MMI: Select on the home screen: VEHICLE > Settings & Service > Garage door opener.
> Press the 4 button.
Opening and closing
» Press the 7 button for the system that you would like to rename.
» Select: Rename. If necessary, delete the preset name, such as Garage door opener 1.
» Follow the instructions in the MMI. Deleting programmed systems The programmed systems can be deleted individually or all at once.
» Applies to: MMI: Select on the home screen: VEHICLE > Settings & Service > Garage door opener.
» Press the 4 button.
» To delete an individual system, press the 1]
button for the desired system. If the checkmark ¥ is set, select: Delete.
» To delete all systems, select: All > Delete.
— Make sure the batteries in the hand transmitter are charged before starting the programming process.
~The programming process may take up to 30 seconds. It may be necessary for the hand transmitter to be pressed again in the meantime.
~The garage door opener may need to be synchronized with the system after programming. Follow the manufacturer's instructions for doing this.
In some cases, the system may need to be programmed in a different mode (“D mode”). — Switch the ignition on. — Applies to: MMI: Select on the home screen: VEHICLE > Settings & Service > Garage door opener.
—Press and hold the desired button @). — Select Yes, in D mode and follow the instructions on the MMI.
Download Manual