Instrument cluster
1. Tachometer
2. Turn signal indicators
3. Speedometer
4.Warning and indicator lights
5. Engine temperature gauge
6. Fuel gauge
7. Odometer/Tripmeter*
* if equipped
❈ The actual cluster in the vehicle may differ from the illustration.
Instrument panel illumination
Press the illumination control switch to adjust the instrument panel illumination intensity. For instrument cluster type A, the vehicle’s parking lights or headlights should be on to adjust the instrument panel illumination.
Gauges
Speedometer
The speedometer indicates the speed of the vehicle.
The speedometer is calibrated in miles per hour and/or kilometers per hour.
Tachometer
The tachometer indicates the approximate number of engine revolutions per minute (rpm).
Use the tachometer to select the correct shift points and to prevent lugging and/or over-revving the engine.
When the door is open, or if the engine is not started within 1 minute, the tachometer pointer may move slightly in ON position with the engine OFF. This movement is normal and will not affect the accuracy of the tachometer once the engine is running.
CAUTION
Do not operate the engine within the tachometer's RED ZONE. This may cause severe engine damage.
Engine temperature gauge
This gauge shows the temperature of the engine coolant when the ignition switch is ON.
Do not continue driving with an overheated engine. If your vehicle overheats, refer to “If the engine overheats” in section 6.
CAUTION
If the gauge moves beyond the normal range area toward the “H” position, it indicates overheating that may damage the engine.
WARNING
Never remove the radiator cap when the engine is hot. The engine coolant is under pressure and could cause severe burns. Wait until the engine is cool before adding coolant to the reservoir.
Fuel gauge
The fuel gauge indicates the approximate amount of fuel remaining in the fuel tank. The fuel tank capacity is given in section 8. The fuel gauge is supplemented by a low fuel warning light, which will illuminate when the fuel tank is near empty.
On inclines or curves, the fuel gauge may fluctuate or the low fuel warning light may come on earlier than usual due to the movement of fuel in the tank.
WARNING - Fuel gauge
Running out of fuel can expose vehicle occupants to danger. You must stop and obtain additional fuel as soon as possible after the warning light comes on or when the gauge indicator comes close to the E level.
CAUTION
Avoid driving with a extremely low fuel level. Running out of fuel could cause the engine to misfire, damaging the catalytic converter.
Odometer (mi. or km)
The odometer indicates the total distance the vehicle has been driven. You will also find the odometer useful to determine when periodic maintenance should be performed.
Trip computer
The trip computer is a microcomputer controlling the driver information system. It displays information related to driving on the LCD screen when the ignition switch is in the ON position. If the battery is disconnected, then all stored driving information (except odometer) is reset.
Press the TRIP button for less than 1 second to select any mode as follows:
Tripmeter (mi. or km)
TRIP A : Tripmeter A
TRIP B : Tripmeter B
This mode indicates the distance of individual trips selected since the last tripmeter reset.
The meter's working range is from 0.0 to 999.9 miles (0.0 to 999.9 km).
Pressing the RESET button for more than 1 second, when the tripmeter (TRIP A or TRIP B) is being displayed, clears the tripmeter to zero (0.0).
Distance to empty (mi. or km)
This mode indicates the estimated distance to empty based on the current fuel in the fuel tank and the amount of fuel delivered to the engine. When the remaining distance is below 30 miles (50 km), “---” will be displayed and the distance to empty indicator will blink.
The meter’s working range is from 30 to 999 miles (50 to 999 km).
Average fuel economy (if equipped) (MPG or l/100 km)
This mode calculates the average fuel consumption from the total fuel used and the distance since the last average economy reset. The total fuel used is calculated from the fuel consumption input. For an accurate calculation, drive more than 0.03 miles (50 m).
Pressing the RESET button for more than 1 second, when the average fuel economy is being displayed, clears the average fuel consumption to zero (----).
If the vehicle speed exceeds 1.6 MPH (1km/h) after being refueled with more than 1.6 gallons (6 l), the average fuel economy will be cleared to zero (----).
Instant fuel consumption (if equipped) (l/100 km or MPG)
This mode calculates the instant fuel consumption of the last few seconds.
✽ NOTICE
- • If the vehicle is not on level ground or the battery power has been interrupted, the “Distance to empty” function may not operate correctly. The trip computer may not register additional fuel if less than 6 liters (1.6 gallons) of fuel are added to the vehicle.
- • The fuel consumption and distance to empty may vary significantly based on driving conditions, driving habits, and condition of the vehicle.
- • The distance to empty value is an estimate of the available driving distance. This may differ from the actual driving distance available.
Average speed (MPH or km/h)
This mode calculates the average speed of the vehicle since the last average speed reset.
Even if the vehicle is not in motion, the average speed keeps changing while the engine is running.
Pressing the RESET button for more than 1 second, when the average speed is being displayed, clears the average speed to zero (---).
Elapsed time
This mode indicates the total time traveled since the last driving time reset. Even if the vehicle is not in motion, the driving time keeps increasing while the engine is running.
The meter’s working range is from 00:00~99:59.
Pressing the RESET button for more than 1 second, when the driving time is being displayed, clears the driving time to zero (00:00).
Distance to service (if equipped)
After selecting the maintenance of engine oil, if service is required, a corresponding message will be displayed.
Maintenance (if equipped)
1. When the vehicle is at a standstill, pressing the TRIP button for more than 2 seconds with the ENGINE START/ STOP button in the ON position or engine running, the LCD display on the cluster will change to the "User Setting" mode.
You can move to the items by pressing the TRIP button and select the item by pressing the RESET button.
2. In the "User Setting" mode select "Maintenance".
3. Select the desired maintenance schedule.
4. If finished, you can come out of the Maintenance mode by pressing the TRIP button for more than 2 seconds.
✽ NOTICE
If service is required, "Engine oil service required" message will be displayed. If you would like to reset or inactivate the maintenance system, press the reset button.
The display will change to "Oil Service Message" mode.
You can move to items by pressing the TRIP button and select the desired items by pressing the RESET button.
Vehicle option
When the vehicle is at a standstill, pressing the TRIP button for more than 2 seconds with the engine start/stop button in the ON position or engine running, the LCD screen on the cluster will change to the vehicle setting mode.
You can change the item by pressing the TRIP button and choose the item by pressing the RESET button.
Auto door lock (if equipped)
Off - The auto door lock operation will be canceled.
Speed - All doors will be automatically locked when the vehicle speed exceeds 15km/h (9.3mph).
Shift Lever - All doors will be automatically locked if the shift lever is shifted from the P(Park) position to the R(Reverse), N(Neutral) or D(Drive) position.
Auto Triple Turn (One-touch triple turn signal) (if equipped)
On - The lane change signals will blink 3 times when the turn signal lever is moved slightly.
Off - The Auto Triple Turn function will be inactivated.
Auto door unlock (if equipped)
Off - The auto door unlock operation will be canceled.
Key Out - All doors will be automatically unlocked when the ignition key is removed from ignition switch (or smart key is removed from the smart key holder).
Shift Lever - All doors will be automatically unlocked if the shift lever is shifted to the P(Park) position.
AVG fuel economy
Auto Reset - The average fuel economy will reset automatically when you drive after refueling.
Manual Reset - The average fuel economy will not reset automatically when you drive after refueling.
Headlamp escort
On - If you turn the ignition switch to the ACC or OFF position with the headlamp ON, the headlamp remain on for about 20 minutes. And the head lamp welcome operation will be activated. Refer to the [LIGHTING] in this chapter.
Off - The headlamp escort and headlamp welcome operation will be canceled.
✽ NOTICE
- • If the vehicle is not on level ground or the battery power has been interrupted, the “Distance to empty” function may not operate correctly. The trip computer may not register additional fuel if less than 1.6 gallons (6 liters) of fuel are added to the vehicle.
- • The fuel consumption and distance to empty values may vary significantly based on driving conditions, driving habits, and condition of the vehicle.
- • The distance to empty value is an estimate of the available driving distance. This value may differ from the actual driving distance available.
Warnings and indicators
All warning lights are checked by turning the ignition switch ON (do not start the engine). Any light that does not illuminate should be checked by an authorized HYUNDAI dealer.
After starting the engine, check to make sure that all warning lights are off. If any are still on, this indicates a situation that needs attention. When releasing the parking brake, the brake system warning light should go off. The fuel warning light will stay on if the fuel level is low.
ECO indicator (if equipped)
Active ECO system (if equipped)
When the active ECO is operating the ECO indicator is green.
For more detailed information, refer to “Active ECO” in chapter 5.
Air bag warning light
This warning light will illuminate for approximately 6 seconds each time you turn the ignition switch to the ON position.
This light also comes on when the Supplemental Restraint System (SRS) is not working properly. If the SRS air bag warning light 
does not come on, or continuously remains on after operating for about 6 seconds when you turned the ignition switch to the ON position or started the engine, or if it comes on while driving, have the SRS inspected by an authorized HYUNDAI dealer.
Anti-lock brake system (ABS) warning light
This light illuminates if the ignition switch is turned ON and goes off in approximately 3 seconds if the system is operating normally.
If the ABS warning light remains on, comes on while driving, or does not come on when the ignition switch is turned to the ON position, this indicates that there may be a malfunction with the ABS.
If this occurs, have your vehicle checked by an authorized HYUNDAI dealer as soon as possible. The normal braking system will still be operational, but without the assistance of the anti-lock brake system.
If the ABS warning light turns on while driving
1.Park the vehicle in a safe place and turn off the engine.
2.Turn on the engine again.
3.If the warning light illuminates and turns off in approximately 3 seconds, the system is operating normally.
If the warning light does not turn off, have your vehicle checked by an authorized HYUNDAI dealer as soon as possible.
Electronic brake force distribution (EBD) system warning light
If these two warning lights illuminate at the same time while driving, your vehicle may have a malfunction with the ABS and EBD system.
In this case, your ABS and regular brake system may not work normally. Have the vehicle checked by an authorized HYUNDAI dealer as soon as possible.
WARNING
If the both ABS and brake warning lights are on and stay on, your vehicle’s brake system will not work normally during sudden braking. In this case, avoid high speed driving and abrupt braking. Have your vehicle checked by an authorized HYUNDAI dealer as soon as possible.
✽ NOTICE
If the ABS warning light or EBD warning light is on and stays on, the speedometer or odometer/tripmeter may not work. In this case, have your vehicle checked by an authorized HYUNDAI dealer as soon as possible.
Seat belt warning
The driver's seat belt warning light and chime will activate to the following table when the ignition switch is in "ON" position.
*1 Warning pattern repeats 11 times with interval 24 seconds. If the driver's seat belt is buckled, the light will stop within 6 seconds and chime will stop immediately.
*2 The light will stop within 6 seconds and chime will stop immediately.
Turn signal indicator
The blinking arrows on the instrument panel show the direction indicated by the turn signals. If the arrow comes on but does not blink, blinks more rapidly than normal, or does not illuminate at all, a malfunction in the turn signal system is indicated. Your dealer should be consulted for repairs.
High beam indicator
This indicator illuminates when the headlights are on and in the high beam position or when the turn signal lever is pulled into the Flash-to-Pass position.
Tail light indicator
This indicator illuminates when the tail lights are on.
Engine oil pressure warning light
This warning light indicates the engine oil pressure is low.
If the warning light illuminates while driving:
1. Drive safely to the side of the road and stop.
2. With the engine off, check the engine oil level. If the level is low, add oil as required.
If the warning light remains on after adding oil or if oil is not available, call an authorized HYUNDAI dealer.
CAUTION
If the engine is not stopped immediately after the engine oil pressure warning light is illuminated, severe damage could result.
CAUTION
If the oil pressure warning light stays on while the engine is running, serious engine damage may result. The oil pressure warning light comes on whenever there is insufficient oil pressure. In normal operation, it should come on when the ignition switch is turned on, then go out when the engine is started. If the oil pressure warning light stays on while the engine is running, there is a serious malfunction.
If this happens, stop the car as soon as it is safe to do so, turn off the engine and check the oil level. If the oil level is low, fill the engine oil to the proper level and start the engine again. If the light stays on with the engine running, turn the engine off immediately. In any instance where the oil light stays on when the engine is running, the engine should be checked by an authorized HYUNDAI dealer before the car is driven again.
Parking brake & brake fluid warning light
Parking brake warning
This light is illuminated when the parking brake is applied with the ignition switch in the START or ON position. The warning light should go off when the parking brake is released.
Low brake fluid level warning
If the warning light remains on, it may indicate that the brake fluid level in the reservoir is low.
If the warning light remains on:
1. Drive carefully to the nearest safe location and stop your vehicle.
2. With the engine stopped, check the brake fluid level immediately and add fluid as required. Then check all brake components for fluid leaks.
3. Do not drive the vehicle if leaks are found, the warning light remains on or the brakes do not operate properly. Have the vehicle towed to any authorized HYUNDAI dealer for a brake system inspection and necessary repairs.
Your vehicle is equipped with a dualdiagonal braking system. This means you still have braking on two wheels even if one of the brake circuits is damaged or malfunctions. With only one of the circuits working, more than normal pedal travel and greater pedal pressure are required to stop the car. Also, the car will not stop in as short a distance with only a portion of the brake system working. If the brakes fail while you are driving, shift to a lower gear for additional engine braking and stop the car as soon as it is safe to do so.
To check bulb operation, check whether the parking brake and brake fluid warning light illuminates when the ignition switch is in the ON position.
WARNING
Driving the vehicle with a warning light on is dangerous. If the brake warning light remains on, have the brakes checked and repaired immediately by an authorized HYUNDAI dealer.
Low tire pressure telltale
The low tire pressure telltale illuminates when one or more of your tires is significantly underinflated.
Inflate your tires to the correct inflation pressure.
The low tire pressure telltale will illuminate after it blinks for approximately one minute when there is a problem with the Tire Pressure Monitoring System. If this occurs, have the system checked by an authorized HYUNDAI dealer as soon as possible.
For details, refer to the TPMS on chapter 6.
WARNING - Low tire pressure
Significantly low tire pressure makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances. Continued driving on tires with low pressure will cause the tires to overheat and fail.
WARNING - Safe stopping
- • The TPMS cannot alert you to severe and sudden tire damage caused by external factors.
- • If you feel any vehicle instability, immediately take your foot off the accelerator, apply the brakes gradually and with light force, and slowly move to a safe position off the road.
Automatic/Manual/DCT transaxle shift position indicator (if equipped)
The indicator displays which automatic /manual/DCT transaxle shift lever is selected.
In DS mode, the “S” indicatror displays in cluster. For more detailed information about DS mode, refer to the chapter 5.
WARNING - DCT
- • When the problem of gear system occurs, the transaxle indicator will blink. For your safety, take your vehicle to an authorized HYUNDAI dealer and have the system checked.
- • When the clutch is overheated, the safe protection mode operates. According to the safe protection mode, the transaxle indicator blinks with buzzer sound. In this time, the LCD warning about safe protection mode also displays. In this condition, the driving may not be smoothly. If you ignore this warning, the vehicle may not drive smoothly and the system may have problem. For the good condition of vehicle, apply the parking brake and stop the vehicle for few seconds before driving off.
Charging system warning light
This warning light indicates a malfunction of either the generator or electrical charging system.
If the warning light comes on while the vehicle is in motion:
1. Drive to the nearest safe location.
2. With the engine off, check the generator drive belt for looseness or breakage.
3. If the belt is adjusted properly, a problem exists somewhere in the electrical charging system. Have an authorized HYUNDAI dealer correct the problem as soon as possible.
✽ NOTICE
When the charging system warning light comes on or the voltage is low (when the alteranator (or battery) does not operate normally or it malfunctions), the steering wheel may get heavy and become difficult to control operate abnormally.
Front fog light indicator
This light comes on when the front fog lights are ON.
Trunk lid open warning light
This warning light illuminates when the trunk lid is not closed securely with the ignition in any position.
Door open warning light
This indicator illuminates when a door is not closed securely.
Immobilizer indicator
Without smart key system
This light illuminates when the immobilizer key is inserted and turned to the ON position to start the engine.
At this time, you can start the engine.The light goes out after the engine is running. If this light blinks when the ignition switch is in the ON position before starting the engine, have the system checked by an authorized HYUNDAI dealer.
With smart key system (if equipped)
If any of the following occurs in a vehicle equipped with the smart key, the immobilizer indicator illuminates, blinks or the light goes off.
- When the smart key is in the vehicle, if the engine start/stop button is turned to the ON position, the indicator will illuminate until the engine is started. However, when the smart key is not in the vehicle, if the engine start/stop button is depressed, the indicator will blink for a few minutes to indicate that you will not be able to start the engine.
- When the ignition switch is turned to the ON position and the indicator turns off after 2 seconds, the system may need repair. Have the vehicle checked by an authorized HYUNDAI dealer.
- When the battery is weak, if the engine start/stop button is depressed, the indicator will blink and you will not be able to start the engine. However, you may still be able to start the engine by pressing the engine start/stop button with the smart key. If smart key system related parts need repair, the indicator blinks.
Low fuel level warning light
This warning light indicates the fuel tank is nearly empty. When it comes on, you should add fuel as soon as possible. Driving with the fuel level warning light on or with the fuel level below “E” can cause the engine to misfire and damage the catalytic converter.
Malfunction indicator light (MIL) (check engine light)
This indicator light is part of the Engine Control System which monitors various emission control system components. If this light illuminates while driving, it indicates that a potential malfunction has been detected somewhere in the emission control system.
This light will also illuminate when the ignition switch is turned to the ON position, and will go out in a few seconds after the engine is started. If it illuminates while driving, or does not illuminate when the ignition switch is turned to the ON position, take your vehicle to your nearest authorized HYUNDAI dealer and have the system checked.
Generally, your vehicle will continue to be drivable, but have the system checked by an authorized HYUNDAI dealer promptly.
CAUTION
- • Prolonged driving with the Malfunction Indicator Light illuminated may cause damage to the emission control systems which could effect drivability and/or fuel economy.
- • If the Malfunction Indicator Light illuminates or blinks, potential catalytic converter damage is possible. This could result in loss of engine power. Have the Engine Control System inspected as soon as possible by an authorized HYUNDAI dealer.
ESC indicator (Electronic Stability Control)
The ESC indicator will illuminate when the ignition switch is turned ON, but should go off after approximately 3 seconds. When the ESC is on, it monitors the driving conditions. Under normal driving conditions, the ESC light will remain off. When a slippery or low traction condition is encountered, the ESC will operate, and the ESC indicator will blink to indicate the ESC is operating.
The ESC indicator stays on when the ESC may have a malfunction. Take your car to an authorized HYUNDAI dealer and have the system checked.
ESC OFF indicator
The ESC OFF indicator will illuminate when the ignition switch is turned ON, but should go off after approximately 3 seconds. To switch to ESC OFF mode, press the ESC OFF button. The ESC OFF indicator will illuminate indicating the ESC is deactivated.
Cruise indicator (if equipped)
CRUISE indicator
The indicator light illuminates when the cruise control system is enabled.
The cruise indicator light in the instrument cluster is illuminated when the cruise control ON-OFF button on the steering wheel is pushed.
The indicator light turns off when the cruise control ON-OFF button is pushed again. For more information about the use of cruise control, refer to “Cruise control system or Smart cruise control system” in section 5.
Cruise SET indicator
The indicator light illuminates when the cruise function switch (SET- or RES+) is ON.
The cruise SET indicator light in the instrument cluster is illuminated when the cruise control switch (SET- or RES+) is pushed. The cruise SET indicator light does not illuminate when the cruise control switch (CANCEL) is pushed or the system is disengaged.
Electronic power steering (EPS) system warning light
This indicator light comes on after the ignition key is turned to the ON position and then it will go out.
This light also comes on when the EPS needs repairs. If it comes on while driving, have your vehicle inspected by an authorized HYUNDAI dealer.
Steering effort may increase significantly if this lamp illuminates. See EPS system in this section.
Key reminder warning chime (if equipped)
Without smart key
If the driver’s door is opened while the ignition key is left in the ignition switch (ACC or LOCK position), the key reminder warning chime will sound. This helps prevent you from locking your keys in the vehicle. The chime sounds until the key is removed from the ignition switch or the driver’s door is closed.
With smart key
If the driver’s door is opened while the smart key is in the vehicle with the engine start/stop button in ACC, the key reminder warning chime will sound. The chime sounds until the driver’s door is closed.
KEY OUT indicator (if equipped)
When the ignition switch is in the ACC or ON position, if any door is open, the system checks for the smart key. If the smart key is not in the vehicle, the indicator will blink, and if all doors are closed, the chime will also sound for about 5 seconds. The indicator will turn off while the vehicle is moving. Keep the smart key in the vehicle.
Fuel cap open warning indicator
This warning light indicates the fuel filler cap is not tight securely. Always make sure that the fuel filler cap is tight.
LCD display warning (if equipped)
Door open ! (if equipped)
It displays the corresponding door or tailgate that is not closed securely.
Low Tire Pressure (if equipped)
It displays the corresponding tire that is low with pressure. For details, refer to “TPMS” in section 6.
❈ The actual indicator in LCD display may differ from the illustration.
Key is not in vehicle
If the smart key is not in the vehicle and if any door is opened or closed with the ENGINE START/ STOP button in the ACC, ON, or START position, the warning illuminates on the LCD display. Also, the chime sounds for 5 seconds when the smart key is not in the vehicle and the door is closed.
Always have the smart key with you.
Low key battery
If the ENGINE START/STOP button turns to the OFF position when the smart key in the vehicle discharges, the warning illuminates on the LCD display for about 10 seconds. Also, the warning chime sounds once. Replace the battery with a new one.
Press brake pedal to start engine (Automatic transaxle)
If the ENGINE START /STOP button turns to the ACC position twice by pressing the button repeatedly without depressing the brake pedal, the warning illuminates on the LCD display for about 10 seconds to indicate that you should depress the brake pedal to start the engine.
Press clutch pedal to start engine (Manual transaxle)
If the ENGINE START /STOP button turns to the ACC position twice by pressing the button repeatedly without depressing the clutch pedal, the warning illuminates on the LCD display for about 10 seconds to indicate that you should depress the clutch pedal to start the engine.
Shift to "P" position (Automatic transaxle)
If you try to turn off the engine without the shift lever in the P (Park) position, the ENGINE START/ STOP button will turn to the ACC position. If the button is pressed once more it will turn to the ON position. The warning illuminates on the LCD display for about 10 seconds to indicate that you should press the ENGINE START/STOP button with the shift lever in the P (Park) position to turn off the engine.
Also, the warning chime sounds for about 10 seconds. (if equipped)
Press start button again
If you can not operate the ENGINE START/ STOP button when there is a problem with the ENGINE START/STOP button system, the warning illuminates for 10 seconds and the chime sounds continuously to indicate that you could start the engine by pressing the ENGINE START/STOP button once more.
The chime will stop if the ENGINE START/STOP button system works normally or the theft alarm system is armed. If the warning illuminates each time you press the ENGINE START/STOP button, take your vehicle to an authorized HYUNDAI dealer and have the system checked.
Shift to "P" or "N" to start the engine (Automatic transaxle)
If you try to start the engine with the shift lever not in the P(Park) or N(Neutral) position, the warning illuminates for about 10 seconds on the LCD display.
You can also start the engine with the shift lever in the N(Neutral) position, but for your safety start the engine with the shift lever in the P(Park) position.
Press start button while turn steering
If the steering wheel does not unlock normally when the ENGINE START/ STOP button is pressed, the warning illuminates for 10 seconds on the LCD display. Also, the warning chime sounds once and the ENGINE START/STOP button light blinks for 10 seconds.
When you are warned, press the ENGINE START/STOP button while turning the steering wheel right and left.
Press start button with smart key
If you press the ENGINE START/ STOP button while the warning “Key is not detected” illuminates the warning “Please press the start button with smart key” illuminates for 10 seconds on the LCD display. Also, the immobilizer indicator blinks for 10 seconds.
Check stop lamp fuse
When the stop lamp fuse is disconnected, the warning illuminates for 10 seconds on the LCD display. Replace the fuse with a new one. If that is not possible you can start the engine by pressing the ENGINE START/STOP button for 10 seconds in ACC.
Stop when safe protection mode on
When the clutch is overheated, this display will be displayed. In this moment, the driving may not be smoothly. If you ignore this warning, the vehicle may not drive smoothly and the system may have problem. For the good condition of vehicle, stop the vehicle for few seconds.
Rear parking assist warning (if equipped)
It displays the area an obstacle is detected while moving rearward.
For details, refer to “Rear parking assist system” in section 4.
Key is not detected
If the smart key is not in the vehicle or is not detected and you press the ENGINE START/ STOP button, the warning illuminates on the LCD display for 10 seconds. Also, the immobilizer indicator blinks for 10 seconds.
Check steering wheel lock
If the steering wheel does not lock normally when the ENGINE START/STOP button turns to the OFF position, the warning illuminates for 10 seconds on the LCD display. Also, the warning chime sounds for 3 seconds and the ENGINE START/STOP button light blinks for 10 seconds.
Download Manual