iPod* player operation without Navigation System (if so equipped)
Connecting iPod
WARNING
Do not connect, disconnect or operate the USB device while driving. Doing so can be a distraction. If distracted you could lose control of your vehicle and cause an accident or serious injury.
CAUTION
- Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the port. Make sure that the USB device is connected correctly into the USB port.
- Do not grab the USB port cover (if so equipped) when pulling the USB device out of the port. This could damage the port and the cover.
- Do not leave the USB cable in a place where it can be pulled unintentionally.
Pulling the cable may damage the port.
For additional information, refer to your device manufacturer's owner information regarding the proper use and care of the device.
To connect an iPod to the vehicle so that the iPod can be controlled with the audio system controls and display screen, use the USB Connection port located beneath the heater and air conditioner controls. Connect the iPod- specific end of the cable to the iPod and the USB end of the cable to the USB Connection port on the vehicle. If your iPod supports charging via a USB connection, its battery will be charged while connected to the vehicle with the ignition switch in the ACC or ON position.
While connected to the vehicle, the iPod can only be operated by the vehicle audio controls.
To disconnect the iPod from the vehicle, remove the USB end of the cable from the USB Connection port on the vehicle, then remove the cable from the iPod.
* iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
Compatibility
The following models are compatible:
- iPod 5th Generation (firmware version 1.3 or later)
- iPod Classic (80GB) (firmware version 1.1.2PC or later)
- iPod Classic (120GB) (firmware version 2.0.1PC or later)
- iPod nano - 1st generation (firmware version 1.3.1 or later)
- iPod nano - 2nd generation (firmware version 1.1.3 or later)
- iPod nano - 3rd generation (firmware version 1.1.3PC or later)
- iPod nano - 4th generation (firmware version 1.0PC or later)
- iPod nano - 5th generation (8GB) (firmware version 1.0.2PC or later)
- iPod nano - 5th generation (16GB) (firmware version 1.0.1PC or later)
- iPod nano - 6th generation (8GB) (firmware version 1.2PC or later)
- iPod nano - 6th generation (8GB) (firmware version 1.1PC or later)
- iPod Touch - 1st generation (firmware version 2.2.1 or later)
- iPod Touch - 2nd generation (firmware version 2.2.1 or later)
- iPod Touch - 3rd generation (firmware version 3.1.3 or later)
- iPod Touch - 4th generation (firmware version 4.3.5 or later)
- iPhone 3G (firmware version 4.1 or later)
- iPhone 3GS (firmware version 4.3 or later)
- iPhone 4 (firmware version 5.0 or later)
- iPhone 4S (firmware version 5.1 or later)
- iPad (firmware version 4.3.2 or later)
- iPad 2 (firmware version 4.3.3 or later)
Make sure that your iPod firmware is updated to the version indicated above.
Audio main operation
Place the ignition switch to the ACC or ON position. Then, press the iPod MENU button or MEDIA button repeatedly to switch to the iPod mode.
If the audio system is turned off while the iPod is playing, the iPod plays when the audio system is turned back on.
If the audio system is off, pressing the iPod MENU button or MEDIA button turns the audio system on and plays the iPod.
If the audio system is on, the audio system automatically begins playing tracks from the iPod when it is plugged into the connection port.
SEEK/CAT or TRACK buttons
Press the SEEK/CAT or TRACK buttons 
or 
to skip backward or forward one track.
Press and hold the SEEK/CAT or TRACK buttons 
or 
for 1.5 seconds while a track is playing to reverse or fast forward the track being played. The track plays at an increased speed while reversing or fast forwarding. When the button is released, the track returns to normal play speed.
(RPT) REPEAT
When the RPT button is pressed while a track is being played, the play pattern can be changed as follows: Repeat Off → 1 Track Repeat → All Repeat → Repeat Off
1 Track Repeat: the current track will be repeated.
All Repeat: all songs in the current list are repeated.
Repeat Off: no repeat play pattern is applied.
(RDM) RANDOM
When the RDM button is pressed while a track is being played, the play pattern can be changed as follows: Shuffle Off → Track Shuffle → Album Shuffle → Shuffle Off
Track Shuffle: the tracks in the current list will be played randomly.
Album Shuffle: the albums in the current list will be played randomly.
Shuffle Off: no random play pattern is applied.
BACK button
When the BACK button is pressed, it returns to the previous menu.
iPod* player operation with Navigation System (if so equipped)
Connecting a device to the USB connection port
WARNING
Do not connect, disconnect or operate the USB device while driving. Doing so can be a distraction. If distracted you could lose control of your vehicle and cause an accident or serious injury.
CAUTION
- Do not force the USB device into the USB port. Inserting the USB device tilted or up-side-down into the port may damage the port. Make sure that the USB device is connected correctly into the USB port.
- Do not grab the USB port cover (if so equipped) when pulling the USB device out of the port. This could damage the port and the cover.
- Do not leave the USB cable in a place where it can be pulled unintentionally.
Pulling the cable may damage the port.
For additional information, refer to your device manufacturer's owner information regarding the proper use and care of the device.
The USB (Universal Serial Bus) connection port is located beneath the heater and air conditioner controls. Insert the USB device into the connection port.
When a compatible storage device is plugged into the connection port, compatible audio files on the storage device can be played through the vehicle's audio system.
Audio file operation
AUX (auxiliary) button
Place the ignition switch in the ON or ACC position and press the AUX button to switch to the USB input mode. If another audio source is playing and a USB memory device is inserted, press the AUX button until the center display changes to the USB memory mode.
If the system has been turned off while the USB memory was playing, press the ON-OFF button to restart the USB memory.
Play information
Information about the audio files being played is shown on the display screen of the vehicle's audio system. Touch "Browse" to display the list of folders and files on the USB device. Touch the name of a song on the screen to begin playing that song.
SEEK buttons
Press the
button while an audio file on the USB device is playing to return to the beginning of the current track. Press the 
button several times to skip backward several tracks.
Press the
button while an audio file on the USB device is playing to advance one track.
Press the 
button several times to skip forward several tracks. If the last track in a folder on the USB device is skipped, the first track of the next folder is played.
REPEAT button
When the RPT button is pressed while an audio file on the USB device is playing, the play pattern can be changed as follows: Track Repeat: the current track will be repeated.
Folder Repeat: the current folder will be repeated.
OFF: No repeat play pattern is applied. The indicator on the display will turn off.
The current play pattern of the USB device is displayed on the screen unless no pattern is applied.
Random and repeat play mode
While files on a USB device are playing, the play pattern can be altered so that songs are repeated or play randomly.
Random
Touch the "Random" key to apply a random play pattern to the USB device. To cancel random mode, touch the "Random" key again.
Repeat
Touch the "Repeat" key to apply a repeat play pattern to the USB device. To cancel repeat mode, touch the "Repeat" key again.
Download Manual