Cruise Control
With cruise control, a speed of about 40 km/h (25 mph) or more can be maintained without keeping your foot on the accelerator. Cruise control does not work at speeds below about 40 km/h (25 mph). If the Traction Control System (TCS) or StabiliTrak/Electronic Stability Control (ESC) system begins to limit wheel spin while using cruise control, the cruise control automatically disengages. See Traction Control/Electronic Stability Control 0 212. If a collision alert occurs when cruise control is activated, cruise control is disengaged. See Forward Collision Alert (FCA) System 0 233.
When road conditions allow the cruise control to be safely used, cruise control can be turned back on. Turning off the TCS or StabiliTrak/ESC system will disengage the cruise control. If the brakes are applied, cruise control disengages.
J : Press to turn the system on and off. A white indicator appears in the instrument cluster when cruise is turned on. RES+ : If there is a set speed in memory, press briefly to resume to that speed or press and hold to accelerate. If the cruise control is already active, use to increase vehicle speed.
SET− : Press briefly to set the speed and activate cruise control. If the cruise control is already active, use to decrease vehicle speed. * : Press to disengage cruise control without erasing the set speed from memory.
Setting Cruise Contro
If J is on when not in use, SET− or RES+ could get pressed and go into cruise when not desired. Keep J off when cruise is not being used. 1. Press J. 2. Get up to the desired speed. 3. Press and release SET−. The desired set speed briefly appears in the instrument cluster. 4. Remove your foot from the accelerator. When the cruise control has been set to the desired speed, a green cruise control indicator appears on the instrument cluster.
Resuming a Set Speed
If the cruise control is set at a desired speed and then the brakes are applied or * is pressed, the cruise control is disengaged without erasing the set speed from memory.
Once the vehicle speed reaches about 40 km/h (25 mph) or more, press RES+ briefly. The vehicle returns to the previous set speed.
Increasing Speed While Using Cruise Control
If the cruise control system is already activated:
. Press and hold RES+ up until the desired speed is reached, then release it. . To increase vehicle speed in small increments, briefly press RES+. For each press, the vehicle goes about 1 km/h (1 mph) faster.
The speedometer reading can be displayed in either English or metric units. See Instrument Cluster (Midlevel) 0 100 or Instrument Cluster (Uplevel) 0 103 or Instrument Cluster (Base Level) 0 98. The increment value used depends on the units displayed.
Reducing Speed While Using Cruise Control
If the cruise control system is already activated:
. Press and hold SET− until the desired lower speed is reached, then release it. . To decrease the vehicle speed in small increments, briefly press SET−. For each press, the vehicle goes about 1 km/h (1 mph) slower.
The speedometer reading can be displayed in either English or metric units. See Instrument Cluster (Midlevel) 0 100 or Instrument Cluster (Uplevel) 0 103 or Instrument Cluster (Base Level) 0 98. The increment value used depends on the units displayed.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase the vehicle speed. When you take your foot off the pedal, the vehicle will slow down to the previous set cruise speed. While pressing the accelerator pedal or shortly following the release to override cruise, briefly applying SET− will result in cruise set to the current vehicle speed. Using Cruise Control on Hills How well the cruise control will work on hills depends upon the vehicle speed, load, and the steepness of the hills. When going up steep hills, you might have to step on the accelerator pedal to maintain your speed. While on a hill, the transmission may downshift in order to use engine braking to slow the vehicle and maintain the set speed. Also, you may have to brake or shift to a lower gear to keep your speed down. If the brake pedal is applied, cruise control disengages.
Ending Cruise Control
There are four ways to end cruise control:
. Step lightly on the brake pedal. . Press *. . Shift the transmission to N (Neutral). . Press J.
Erasing Speed Memory
The cruise control set speed is erased from memory if J is pressed or if the ignition is turned off.
Adaptive Cruise Control (Advanced)
If equipped with Adaptive Cruise Control (ACC), it allows the driver to select the cruise control set speed and following gap. Read this entire section before using this system. The following gap is the following time between your vehicle and a vehicle detected directly ahead in your path, moving in the same direction. If no vehicle is detected in your path, ACC works like regular cruise control. ACC uses camera and radar sensors. See Radio Frequency Statement 0 344.
If a vehicle is detected in your path, ACC can apply acceleration or limited, moderate braking to maintain the selected following gap. To disengage ACC, apply the brake. If ACC is controlling your vehicle speed when the Traction Control System (TCS) or StabiliTrak/Electronic Stability Control (ESC) system activates, the ACC may automatically disengage. See Traction Control/Electronic Stability Control 0 212. When road conditions allow ACC to be safely used, the ACC can be turned back on. Disabling the TCS or StabiliTrak/ESC system will disengage and prevent engagement of ACC. ACC can reduce the need for you to frequently brake and accelerate, especially when used on expressways, freeways, and interstate highways. When used on other roads, you may need to take over the control of braking or acceleration more often. ACC automatically slows the vehicle down while navigating the curve and may increase speed out of the curve, but will not exceed the set speed.
J : Press to turn the system on or off. The indicator turns white on the instrument cluster when ACC is turned on. RES+ : Press briefly to resume the previous set speed or to increase vehicle speed if ACC is already activated. To increase speed by about 1 km/h (1 mph), press RES+ briefly. To increase speed to the next 5 km/h (5 mph) mark on the speedometer, hold RES+. SET– : Press briefly to set the speed and activate ACC or to decrease vehicle speed if ACC is already activated. To decrease speed by about 1 km/h (1 mph), press SET– briefly. To decrease speed to the next 5 km/h (5 mph) mark on the speedometer, hold SET– .
* : Press to disengage ACC without erasing the selected set speed. [ : Press to select a following gap time (or distance) setting for ACC of Far, Medium, or Near. The speedometer reading can be displayed in either English or metric units. See Instrument Cluster (Midlevel) 0 100 or Instrument Cluster (Uplevel) 0 103 or Instrument Cluster (Base Level) 0 98. The increment value used depends on the units displayed. Switching Between ACC and Regular Cruise Control To switch between ACC and regular cruise control, press and hold *. A Driver Information Display (DIC) message displays. See Vehicle Messages 0 122.
ACC Indicator Regular Cruise Control Indicator
When ACC is engaged, a green o indicator will be lit on the instrument cluster and the following gap will be displayed. When the regular cruise control is engaged, a green J indicator will be lit on the instrument cluster; the following gap will not display. It is recommended to switch from ACC to regular cruise control only, when there are no vehicles ahead of your vehicle. When the vehicle is turned on, the cruise control mode will be set to the last mode used before the vehicle was turned off.
Setting Adaptive Cruise Control
If J is on when not in use, it could get pressed and go into cruise when not desired. Keep J off when cruise is not being used. Select the set speed desired for cruise. This is the vehicle speed when no vehicle is detected in its path. While the vehicle is moving, ACC will not set at a speed less than 25 km/h (15 mph), although it can be resumed when driving at lower speeds. The minimum allowable set speed is 25 km/h (15 mph). To set ACC while moving: 1. Press J. 2. Get up to the desired speed. 3. Press and release SET–. 4. Remove foot from the accelerator. After ACC is set, it may immediately apply the brakes if a vehicle ahead is detected closer than the selected following gap. ACC can also be set while the vehicle is stopped if ACC is on and the brake pedal is applied.
The ACC indicator displays in the instrument cluster. When ACC is turned on, the indicator will be lit white. When ACC is active, the indicator will turn green. Be mindful of speed limits, surrounding traffic speeds, and weather conditions when selecting the set speed. Resuming a Set Speed If the ACC is set at a desired speed and then the brakes are applied, ACC is disengaged without erasing the set speed from memory. To begin using ACC again, press RES+ up briefly. The vehicle returns to the previous set speed. . If the vehicle is moving more than 5 km/h (3 mph), it returns to the previous set speed. . If the vehicle is stopped with the brake pedal applied, press RES+ and release the brake pedal. ACC will hold the vehicle until RES+ or the accelerator pedal is pressed.
A green ACC indicator and the set speed display on the instrument cluster. The vehicle ahead indicator may be flashing if a vehicle ahead was present and moved. See “Approaching and Following a Vehicle” later in this section. Once ACC has resumed, if there is no vehicle ahead, if the vehicle ahead is beyond the selected following gap, or if the vehicle has exited a sharp curve, then the vehicle speed will increase to the set speed. Increasing Speed While ACC Is at a Set Speed If ACC is already activated, do one of the following:
. Use the accelerator to get to the higher speed. Briefly press and release SET– and release the accelerator pedal. The vehicle will now cruise at the higher speed. When the accelerator pedal is pressed, ACC will not brake because it is overridden. While overridden, the ACC indicator will turn blue on the instrument cluster. . Press and hold RES+ up until the desired set speed is displayed, then release it. . To increase vehicle speed in smaller increments, press RES+ briefly. For each press, the vehicle goes 1 km/h or (1 mph) faster. . To increase vehicle speed in larger increments, hold RES+. While holding RES +, the vehicle speed increases to the next 5 km/h (5 mph) step, then continues to increase by 5 km/h (5 mph) at a time. The set speed can also be increased while the vehicle is stopped. . If stopped with the brake applied, press RES+ until the desired set speed is displayed. . If ACC is holding the vehicle at a stop and there is another vehicle directly ahead, pressing RES+ will increase the set speed. . Pressing RES+ when there is no longer a vehicle ahead or the vehicle ahead is pulling away and the brake is not applied will cause the ACC to resume.
When it is determined that there is no vehicle ahead, or the vehicle ahead is beyond the select following gap, then the vehicle speed will increase to the set speed.
Reducing Speed While ACC Is at a Set Speed
Do one of the following:
. Use the brake to get to the desired lower speed. Release the brake and press SET–. The vehicle will now cruise at the lower speed. . Press and hold SET– until the desired lower speed is reached, then release it. . To decrease the vehicle speed in smaller increments, press SET−. For each press, the vehicle goes about 1 km/h (1 mph) slower. . To decrease the vehicle speed in larger increments, press and hold SET−. For each press, the vehicle goes about 5 km/h (5 mph) slower. . To decrease speed while the vehicle is stopped and the brakes are applied, press SET− until the desired set speed is displayed.
Selecting the Follow Distance Gap
When a slower moving vehicle is detected ahead within the selected following gap, ACC will adjust the vehicle's speed and attempt to maintain the follow distance gap selected. Press [ on the steering wheel to adjust the following gap. Each press cycles the gap button through three settings: Far, Medium, or Near. When pressed, the current gap setting displays briefly on the instrument cluster. The gap setting will be maintained until it is changed. Since each gap setting corresponds to a following time (Far, Medium, or Near), the following distance will vary based on vehicle speed. The faster the vehicle speed, the further back your vehicle will follow a vehicle detected ahead. Consider traffic and weather conditions when selecting the following gap. The range of selectable gaps may not be appropriate for all drivers and driving conditions. Changing the gap setting automatically changes the alert timing sensitivity (Far, Medium, or Near) for the Forward Collision Alert (FCA) feature. See Forward Collision Alert (FCA) System 0 233.
Alerting the Driver
If ACC is engaged, driver action may be required when ACC cannot apply sufficient braking because of approaching a vehicle too rapidly. When this condition occurs, the collision alert symbol will flash on the windshield. Either eight beeps will sound from the front, or both sides of the Safety Alert Seat (if equipped) will pulse five times. Touch the Settings icon on the infotainment home page. Select “Vehicle” to display the list of available options and select “Collision/ Detection Systems”. See Defensive Driving 0 188.
Approaching and Following a Vehicle
The vehicle ahead indicator is in the instrument cluster. The vehicle ahead indicator only displays when a vehicle is detected in your vehicle’s path moving in the same direction. If this symbol is not displaying, ACC will not respond to or brake for vehicles ahead. ACC automatically slows the vehicle down and adjusts vehicle speed to follow the vehicle in front at the selected follow gap. The vehicle speed increases or decreases to follow the vehicle in front of you, but will not exceed the set speed. It may apply limited braking, if necessary. When braking is active, the brake lights will come on. The automatic braking may feel or sound different than if the brakes were applied manually. This is normal.
Passing a Vehicle While Using ACC
If the set speed is high enough, and the left turn signal is used to pass a vehicle ahead in the selected following gap, ACC may assist by gradually accelerating the vehicle prior to the lane change.
Irregular Objects Affecting ACC
ACC may have difficulty detecting the following objects:
. Vehicles with cargo extending from the back end. . Non-standard shaped vehicles, such as vehicle transport, vehicles with a side car fitted, or horse carriages. . Objects that are close to the front of your vehicle.
ACC Automatically Disengages
ACC may automatically disengage and the driver will need to manually apply the brakes to slow the vehicle if:
. The sensors are blocked. . The Traction Control System (TCS) or StabiliTrak/ESC system has activated or been disabled. . There is a fault in the system. . The radar falsely reports blockage when driving in a desert or remote area with no other vehicle or roadside objects. . A DIC message may display to indicate that ACC is temporarily unavailable.
The ACC indicator will turn white when ACC is no longer active. In some cases, when ACC will not activate, regular cruise control may be used. See “Switching Between ACC and Regular Cruise Control” previously in this section. Always consider driving conditions before using either cruise control system.
Notification to Resume ACC
ACC will maintain a follow gap behind a detected vehicle and slow your vehicle to a stop behind that vehicle. If the stopped vehicle ahead has driven away and ACC has not resumed, the vehicle ahead indicator will flash as a reminder to check traffic before proceeding. In addition, the left and right sides of the Safety Alert Seat (if equipped) will pulse three times, or three beeps will sound. Touch the Settings icon on the infotainment home page. Select “Vehicle” to display the list of available options and select ”Alert Type” and “Adaptive Cruise Go Notifier” in “Collision/ Detection Systems”. When the vehicle ahead drives away, ACC resumes automatically if the stop was brief. If necessary, press RES+ or the accelerator pedal to resume ACC. If stopped for more than two minutes or if the driver door is opened and the driver seat belt is unbuckled, the ACC automatically applies the Electric Parking Brake (EPB) to hold the vehicle. The EPB status light will turn on. See Electric Parking Brake 0 210. To release the EPB, press the accelerator pedal. A DIC warning message may display indicating to shift to P (Park) before exiting the vehicle. See Vehicle Messages 0 122.
ACC Override
If using the accelerator pedal while ACC is active, the ACC indicator turns blue on the instrument cluster. ACC will resume operation when the accelerator pedal is not being pressed.
Curves in the Road
ACC may operate differently in a sharp curve. It may reduce the vehicle speed if the curve is too sharp.
ACC automatically slows the vehicle down while navigating the curve and may increase speed out of the curve, but will not exceed the set speed.
When following a vehicle and entering a curve, ACC may not detect the vehicle ahead and accelerate to the set speed. When this happens, the vehicle ahead indicator will not appear.
ACC may detect a vehicle that is not in your lane and apply the brakes.
ACC may occasionally provide an alert and/ or braking that is considered unnecessary. It could respond to vehicles in different lanes, signs, guardrails, and other stationary objects when entering or exiting a curve. This is normal operation. The vehicle does not need service.
Other Vehicle Lane Changes
ACC will not detect a vehicle ahead until it is completely in the lane. The brakes may need to be manually applied.
Objects Not Directly in Front of Your Vehicle
The detection of objects in front of the vehicle may not be possible if:
. The vehicle or object ahead is not within your lane. . The vehicle ahead is shifted, not centered, or is shifted to one side of the lane.
Driving in Narrow Lanes
Vehicles in adjacent traffic lanes or roadside objects may be incorrectly detected when located along the roadway.
Do Not Use ACC on Hills and When Towing a Trailer
Do not use ACC when driving on steep hills or when towing a trailer. ACC will not detect a vehicle in the lane while driving on steep hills. The driver will often need to take over acceleration and braking on steep hills, especially when towing a trailer. If the brakes are applied, the ACC disengages.
Disengaging ACC
There are three ways to disengage ACC:
. Step lightly on the brake pedal. . Press *. . Press J.
Erasing Speed Memory
The cruise control set speed is erased from memory if J is pressed or if the ignition is turned off.
Weather Conditions Affecting ACC
System operation may be limited under snow, heavy rain, or road spray conditions.
Accessory Installations and Vehicle Modifications
Do not install or place any object around the front camera windshield area that would obstruct the front camera view. Do not install objects on top of the vehicle that overhang and obstruct the front camera, such as a canoe, kayak, or other items that can be transported on a roof rack system. See Roof Rack System 0 88. Do not modify the hood, headlamps, or fog lamps, as this may limit the camera’s ability to detect an object.
Cleaning the Sensing System
The camera sensor on the windshield behind the rearview mirror and the radar sensors on the front of the vehicle can become blocked by snow, ice, dirt, or mud. These areas need to be cleaned for ACC to operate properly. If ACC will not operate, regular cruise control may be available. See “Switching Between ACC and Regular Cruise Control” previously in this section. Always consider driving conditions before using either cruise control system. For cleaning instructions, see “Washing the Vehicle” under Exterior Care 0 315.
Download Manual