2019 Ford F-150 Owners Manual - Windows and Mirrors

Windows and Mirrors

POWER WINDOWS (IF EQUIPPED)

E176215

Press the control to open the window. Lift the control to close the window.

Note: You may hear a pulsing noise when just one of the windows is open. Lower the opposite window slightly to reduce this noise.

Press or lift the switch fully and release it. Press or lift it again to stop the window.

Note: The window may disable for up to five minutes if you cycle it up and down repeatedly. This helps prevent damage to the motor. Normal operation will resume once the motor cools.

You may lose the one-touch function if the vehicle battery is low.

To reset the function after the battery recharges:

Pull the switch all the way up.

Hold the switch until the glass stops and continue to hold for two seconds.

Press the switch down and operate the window to the full down position. One-touch up will now be functional.

Note: Perform one-touch up re-calibration with the door closed. Calibrating with the door open will cause the window to continuously bounce back.

Bounce-Back (If Equipped)

The window will automatically stop and reverse some distance if it detects an obstacle while closing.

Pull up the window switch and hold within two seconds of the window reaching the bounce-back position. The window will travel up with no bounce-back protection. The window will stop if you release the switch before the window closes fully.

100

Window Lock (If Equipped)

E176216

Press the control to lock or unlock the rear window controls.

E144073

A B C

Left-hand mirror. Adjustment control. Right-hand mirror.

The window switches remain operational for several minutes when you switch the ignition off or until you open either front door.

101

To adjust your mirrors, switch your vehicle on (with the ignition in accessory mode or the engine running) and then:

Select the mirror you want to adjust. The control lights.

Use the adjustment control to adjust the position of the mirror.

Press the mirror control again. The control light turns off.

Push the mirror toward the door window glass. Make sure that you fully engage the mirror in its support when returning it to its original position.

E277400

This feature lets you extend the mirror about 3 in (75 mm). It is useful when towing a trailer. You can manually pull out or push in the mirrors to the desired position.

To fold both mirrors, switch your vehicle on (with the ignition in accessory mode or the engine running) and then:

Press the control.

Press control again to unfold the mirrors.

Note: Do not stop the mirrors midway through their movement. Wait until the mirrors stop moving and press the control again.

The left-hand and right-hand mirrors move at different rates. For example, one mirror may stop while the other one continues to move. This is normal.

Moving the mirrors 10 or more times within one minute, or repeated folding and unfolding of the mirrors while holding the control down during full travel, may disable the system to protect the motors from overheating. Wait approximately three minutes with the vehicle running, and up to 10 minutes with the vehicle off, for the system to reset and for function to return to normal.

If your power-folding mirrors are manually folded, they may not work properly even after you re-position them. You need to reset them if:

The mirrors vibrate when you drive.

The mirrors feel loose.

The mirrors do not stay in the folded or unfolded position.

One of the mirrors is not in its normal driving position.

To reset the power-fold feature, use the power-folding mirror control to fold and unfold the mirrors. You may hear a loud noise as you reset the power-folding mirrors. This sound is normal. Repeat this process as needed each time the mirrors are manually folded.

PowerScope™Power Telescoping Mirrors (If Equipped)

This feature lets you position both mirrors at the same time.

102

To adjust your mirrors, make sure you switch your vehicle on (with the ignition in accessory mode or the engine running) and then:

Press and release the control. It lights.

Press the adjustment control to position the mirrors.

Press the left arrow to extend the mirrors out. Press the right arrow to retract the mirrors in.

Press the up or down arrow to fold the mirrors toward the window glass. Press the up or down arrow again to fold the mirrors out.

Note: Moving the mirrors 10 or more times within one minute, or repeated folding and unfolding of the mirrors while holding the control down during full travel, may disable the system to protect the motors from overheating. Wait approximately three minutes with the vehicle running, and up to 10 minutes with the vehicle off, for the system to reset and for function to return to normal.

Heated Exterior Mirrors (If Equipped) See Heated Exterior Mirrors (page 153). Memory Mirrors (If Equipped)

You can save and recall the mirror positions through the memory function. See Memory Function (page 161).

The driver exterior mirror automatically dims when the interior auto-dimming mirror turns on.

While the vehicle is running, the

forward-facing portion of the appropriate mirror housing blinks when you switch on the direction indicator.

Puddle Lamps (If Equipped)

The lamps on the bottom part of the mirror housing light when you use your transmitter to unlock the doors or when you open a door.

The lower, outer part of the mirror housings light when you switch the headlamps or parking lamps on.

Spot Lamps (If Equipped)

The area lights are on the forward-facing portion of the mirror housing. You can switch them on and off by using the controls located on the instrument panel. See Lighting (page 93).

Each mirror includes a camera.

Integrated Blind Spot Mirror (If Equipped)

103

Blind spot mirrors have an integrated convex mirror built into the upper outboard corner of the exterior mirrors. They can assist you by increasing visibility along the side of your vehicle. The blind spot mirror is only on the driver exterior mirror.

Check the main mirror first before a lane change, then check the blind spot mirror. If no vehicles are present in the blind spot mirror and the traffic in the adjacent lane is at a safe distance, signal that you are going to change lanes. Glance over your shoulder to verify traffic is clear, and carefully change lanes.

E138665

The image of the approaching vehicle is small and near the inboard edge of the main mirror when it is at a distance. The image becomes larger and begins to move outboard across the main mirror as the vehicle approaches (A). The image transitions from the main mirror and begins to appear in the blind spot mirror as the vehicle approaches (B). The vehicle transitions to your peripheral field of view as it leaves the blind spot mirror (C).

Blind Spot Information System (If Equipped)

(page 262).

Note: Do not clean the mirror housing or glass with harsh abrasives, fuel or other petroleum-based cleaning products.

You can adjust the interior mirror to your preference. Some mirrors also have a second pivot point. This lets you move the mirror head up or down and from side to side.

Pull the tab below the mirror toward you to reduce the effect of bright light from behind.

104

Note: Do not block the sensors on the front and back of the mirror. A rear center passenger or raised rear center head restraint may also block light from reaching the sensor.

The mirror dims to reduce the effect of bright light from behind. It returns to normal when the bright light from behind is no longer present or if you shift into reverse (R).

Power Sliding Back Window (If Equipped)

Press and hold the control to open the window. Pull and hold the control to close the window.

Rotate the sun visor toward the side window and extend it rearward for extra shade.

E162197

Lift the cover to switch the lamp on.

The control is on the overhead console.

105

MOONROOF (IF EQUIPPED)

The moonroof controls are located on the overhead console and have a one-touch open and close feature. To stop its movement during one-touch operation, press the control a second time.

E191272

Note: The moonroof stops short of the fully opened position to reduce wind noise or rumbling that may happen with the moonroof fully open. Press and release the control again to open the moonroof fully.

Press and release to vent the moonroof.

Press and release to open the sunshade. The sunshade opens automatically with the moonroof. You can also open the sunshade with the moonroof closed.

Note: The sunshade stops short of its fully opened position for the comfort of rear passengers. To open the sunshade fully, press the control again.

Press and release to close the sunshade.

Press and release to close the moonroof from either the open or vent positions.

The moonroof automatically reverses some distance if an obstacle is detected while closing.

To override this feature, press and hold (E) within two seconds after the roof comes to a stop following a bounce-back reversal.

Moonroof open.

Moonroof vent.

Sunshade open.

Sunshade close.

Moonroof close.

Press and release to open the moonroof.

106