Light bulbs
Light bulbs are installed in various parts of the vehicle to provide lighting inside and outside the vehicle as well as to alert other vehicles.
Bulb replacement precaution
Please keep extra bulbs on hand with appropriate wattage ratings in case of emergencies.
When changing lamps, first turn off the vehicle at a safe place, firmly apply the parking brake and detach the battery's negative (-) terminal.
Warning
Working on the lights
Prior to working on the light, firmly apply the parking brake, ensure that turn the ignition switch and turn off the lights to avoid sudden movement of the vehicle and burning your fingers or receiving an electric shock.
Use only bulbs of the specified wattage.
Caution
Light replacement
Be sure to replace the burned-out bulb with one of the same wattage rating. Otherwise, it may cause damage to the fuse or electric wiring system.
Fully install light bulbs and any parts used to secure them. Failure to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens. To prevent damage or fire, make sure bulbs are fully seated and locked.
Caution
Headlamp Lens
To prevent damage, do not clean the headlamp lens with chemical solvents or strong detergents.
Notice
-
If the light bulb or lamp connector is removed while the lamp is still on, the fuse box's electronic system may log it as a malfunction. Therefore, a lamp malfunction incident may be recorded as a Diagnostic Trouble Code (DTC) in the fuse box.
-
It is normal for an operating lamp to flicker momentarily. This is due to a stabilization function of the vehicle's electronic control device. If the lamp lights up normally after momentarily blinking, then it is functioning as normal.
However, if the lamp continues to flicker several times or turns off completely, there may be an error in the vehicle's electronic control device. So we recommend that you have the vehicle checked by an authorized Kia dealer immediately.
Notice
We recommend that the headlight aiming be adjusted by an authorized Kia dealer after an accident or after the headlight assembly is reinstalled.
Notice
You can find moisture inside the lens of lamps after a car wash or driving in the rain. It is a natural event caused by the temperature difference between the inside and the outside of the lamp and does not mean a problem with its functions. The moisture inside the lamp would disappear if you drive the vehicle with the headlamp turned on, however, the level at which the moisture is removed may differ depending on the size / location / condition of the lamp. If the moisture continues to stay inside the lamp, have the vehicle checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
If you don't have the necessary tools, the correct bulbs and the expertise, consult a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner. In many cases, it is difficult to replace vehicle light bulbs because other parts of the vehicle must be removed before you can get to the bulb. This is especially true if you have to remove the headlamp assembly to get to the bulb(s).
Removing/installing the headlamp assembly can result in damage to the vehicle. If non-genuine parts or substandard bulbs are used, it may lead to blowing a fuse or other wiring damages.
Do not install extra lamps or LEDs to the vehicle. If additional lights are installed, it may lead to lamp malfunctions and flickering. Additionally, the fuse box and other writing may be damaged.
Light bulb position (Front)
Headlamp - Type A
Headlamp - Type B
Headlamp - Type C
Fog lamp - Type A
Fog lamp - Type B
Position lamp
-
Headlamp (High & Low) (Bulb type)
-
Position lamp / Daytime running lamp (Bulb type)
-
Position lamp / Daytime running lamp (LED type)
-
Turn signal lamp (Bulb type)
-
Turn signal lamp (LED type)
-
Headlamp (High) (LED type)
-
Headlamp (Low) (LED type)
-
Front fog lamp (Bulb type)
-
Front fog lamp (LED type)
-
Position lamp (auxiliary) (LED type)
Light bulb position (Rear)
Rear combination lamp - Type A
Rear combination lamp – Type B
License Plate lamp
High Mounted Stop Lamp (HMSL)
-
Tail lamp (Bulb type)
-
Tail lamp / Stop lamp (Bulb type)
-
Tail lamp / Stop lamp (LED type)
-
Stop lamp (LED type)
-
Back up lamp (Bulb type)
-
Rear turn signal lamp (Bulb type)
-
License plate lamp (Bulb type)
-
High mounted stop lamp (Bulb type)
Light bulb position (Side)
-
Side direction indicator lam (Bulb)
-
Side repeater lamp (LED type)
Headlamp bulb
Warning
Halogen bulbs
Handle halogen bulbs with care.
-
Halogen bulbs contain pressurized gas that will produce flying pieces of glass if broken.
-
Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids. Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit. A bulb should be operated only when installed in a headlamp.
-
If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.
-
Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
Replacing headlamp (low/high) / turn signal lamp / position lamp / daytime running lamp bulb (bulb type) (headlamp type A)
-
Headlamp (low and high)
-
Turn signal lamp
-
Position lamp / daytime running lamp
To prepare replacing the lamp bulb:
1-Open the hood.
To replace the headlamp (low/high) bulb:
1-Remove the headlight bulb cover by turning it counterclockwise.
2-Disconnect the headlight bulb socket-connector.
3-Unsnap the headlight bulb retaining wire by depressing the end and pushing it upward.
4-Remove the bulb from the headlight assembly.
5-Install a new headlight bulb and snap the headlight bulb retaining wire into position by aligning the wire with the groove on the bulb.
6-Connect the headlight bulb socket connector.
7-Install the headlight bulb cover by turning it clockwise.
To replace the turn signal lamp, position lamp, daytime running lamp bulb:
1-Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
2-Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
3-Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
4-Push the socket into the assembly and turn the socket clockwise.
Replacing headlamp (low/high) / turn signal lamp bulb (bulb type) (headlamp type B)
-
Headlamp (low and high)
-
Turn signal lamp
To prepare replacing the lamp bulb:
1-Open the hood.
To replace the headlamp (low/high) bulb:
1-Remove the headlight bulb cover by turning it counterclockwise.
2-Disconnect the headlight bulb socket-connector.
3-Unsnap the headlight bulb retaining wire by depressing the end and pushing it upward.
4-Remove the bulb from the headlight assembly.
5-Install a new headlight bulb and snap the headlight bulb retaining wire into position by aligning the wire with the groove on the bulb.
6-Connect the headlight bulb socket connector.
7-Install the headlight bulb cover by turning it clockwise.
To replace the turn signal lamp:
1-Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
2-Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
3-Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
4-Push the socket into the assembly and turn the socket clockwise.
Replacing position lamp / daytime running lamp (LED type) (headlamp type B)
If the position lamp / daytime running lamp LED (1) does not operate, we recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
The LED lamps cannot be replaced as a single component because it is an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the position lamp / daytime running lamp (LED), for it may damage related parts of the vehicle.
Replacing headlamp (high and low) / position lamp / daytime running lamp / turn signal lamp (LED type) (headlamp type C)
If the position lamp / daytime running lamp LED (1) does not operate, we recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
The LED lamps cannot be replaced as a single component because it is an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the position lamp / daytime running lamp (LED), for it may damage related parts of the vehicle.
Replacing position lamp (auxiliary) (LED type)
If the auxiliary lamp LED (1) does not operate, we recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
The LED lamps cannot be replaced as a single component because it is an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the auxiliary lamp (LED), for it may damage related parts of the vehicle.
Replacing front fog lamp (bulb/LED type)
If the front fog lamp (type A, B) does not operate, we recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
Type A
Type B
Replacing side repeater lamp (LED Type) bulb
If the side repeater lamp LED (1), does not operate, we recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
The LED lamps cannot be replaced as a single component because it is an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the side repeater lamp (LED), for it may damage related parts of the vehicle.
We recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
Replacing side repeater lamp bulb (bulb type)
1-Remove the lamp assembly from the vehicle by prying the lens and pulling the assembly out.
2-Disconnect the bulb electrical connector.
3-Separate the socket and the lens parts by turning the socket counterclockwise until the tabs on the socket align with the slots on the lens part.
4-Remove the bulb by pulling it straight out.
5-Insert a new bulb in the socket.
6-Reassemble the socket and the lens part.
7-Connect the bulb electrical connector.
8-Reinstall the lamp assembly to the body of the vehicle.
Replacing rear turn signal lamp / back up lamp bulb / tail lamp / tail and stop lamp bulb (bulb type) (rear combination lamp type A, B)
Type A
Type B
-
Turn signal lamp
-
Back up lamp
-
Tail lamp
-
Tail and stop lamp
To place the lamp bulb:
1-Open the tailgate.
2-Loosen the light assembly retaining screws with a cross-tip screwdriver.
3-Remove the rear combination light assembly from the body of the vehicle.
4-Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
5-Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket.
6-Pull the bulb out of the socket.
7-Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
8-Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
9-Push the socket into the assembly and turn the socket clockwise.
10-Reinstall the light assembly to the body of the vehicle.
Replacing stop lamp / tail and stop lamp (LED type) (rear combination lamp type B)
If the stop lamp (1) or tail and stop lamp (2) does not operate, we recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
The LED lamps cannot be replaced as a single component because it is an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the LED lamps, for it may damage related parts of the vehicle.
Replacing High Mounted Stop Lamp bulb (bulb type)
1-Open the tailgate.
2-Remove the mounting screws of both sides of the service cover using a Philips screwdriver.
3-Remove the three round head cap nut fixing the high mounted stop lamp using a wrench.
4-Pull out the high mounted stop lamp assembly and unplug the connector.
5-Remove the cover from the assembly.
6-Pull out the bulb from the socket.
7-Insert a new bulb in the socket.
8-Install the high mounted stop lamp in the reverse order of removal.
Replacing license plate lamp bulb
1-Using a screwdriver, gently pry the lamp assembly from interior.
2-Remove the bulb by pulling it straight out.
3-Install a new bulb in the socket.
4-Install the lamp assembly to interior.
Replacing map lamp (bulb type) bulb
Warning
Prior to working on the Interior lamps, ensure that the "OFF" button is depressed to avoid burning your fingers or receiving an electric shock.
1-Using a flat-blade screwdriver, gently pry the lens cover from lamp housing.
2-Remove the bulb by pulling it straight out.
3-Install a new bulb in the socket.
4-Align the lens cover tabs with the lamp housing notches and snap the lens into place.
Notice
Be careful not to dirty or damage the lens, lens tab, and plastic housings.
Replacing map lamp (LED type) bulb
If the map lamp (LED) does not operate, we recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
The LED lamps cannot be replaced as a single component because they are part of an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the map lamp (LED), for it may damage related parts of the vehicle.
We recommend that the system be checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
Replacing room lamp (bulb type) bulb
Warning
Prior to working on the Interior lamps, ensure that the "OFF" button is depressed to avoid burning your fingers or receiving an electric shock.
1-Using a flat-blade screwdriver, gently pry the lens cover from lamp housing.
2-Remove the bulb by pulling it straight out.
3-Install a new bulb in the socket.
4-Align the lens cover tabs with the lamp housing notches and snap the lens into place.
Notice
Be careful not to dirty or damage the lens, lens tab, and plastic housings.
Replacing room lamp (LED type) bulb
If the Room lamp (LED) does not operate, have the vehicle checked by a professional workshop. Kia recommends to visit an authorized Kia dealer/service partner.
The LED lamps cannot be replaced as a single component because they are part of an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the Room lamp (LED), for it may damage related parts of the vehicle.
Replacing luggage room lamp (bulb type) bulb
1-Using a flat-blade screwdriver, gently pry the lens cover from lamp housing.
2-Remove the bulb by pulling it straight out.
3-Install a new bulb in the socket.
4-Align the lens cover tabs with the lamp housing notches and snap the lens into place.
Caution
Be careful not to dirty or damage the lens, lens tab, and plastic housings.