Headlamp, Daytime Running Light (DRL), Cornering Lamp, Parking Lamp, Turn Signal Lamp and Side Marker
(1) Headlight (High) (LED)
(2) Headlight (Low) (LED)
(3) Daytime running light / Position lamp/ Turn signal lamp (LED) (if equipped)
(4) Side marker
(5) Side marker
Headlamp
- Open the hood.
- Disconnect the negative battery cable.
- Remove the headlamp bulb cover by turning it counterclockwise.
- Remove the bulb socket from the headlamp assembly by turning it counterclockwise
- Disconnect the headlamp bulb socket-connector.
- Reinstall in the reverse order of removal.
Information
The headlamp aiming should be adjusted after an accident or after the headlamp assembly is reinstalled at an authorized HYUNDAI dealer.
WARNING
Halogen bulb
- Handle halogen bulbs with care. Halogen bulbs contain pressurized gas that will produce flying pieces of glass that could cause injuries if broken.
- Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
• Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids.
• Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
• A bulb should be operated only when installed in a headlamp.
• If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.
Daytime running light (DRL)/Position lamp
If the lamp (LED) does not operate, have the system checked by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.
Turn signal lamp
- Open the hood.
- Disconnect the negative battery cable.
- Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
- Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
- Install a new bulb by inserting it into the socket and rotating it until it locks into place.
- Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
- Push the socket into the assembly and turn the socket clockwise.
Side marker
- Open the hood.
- Disconnect the negative battery cable.
- Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
- Remove the bulb from the socket by pulling out the bulb.
- Insert a new bulb.
- Reinstall in the reverse order of removal.
(1) Cornering lamp (Low beam assist)
(2) Headlamp (Low/High)
(3) Daytime Running Light (DRL)/ Parking lamp
(4) Turn signal lamp
(5) Side marker
Cornering lamp (Low beam assist)
- Open the hood.
- Disconnect the negative battery cable.
- Remove the headlamp bulb cover by turning it counterclockwise.
- Remove the bulb socket from the headlamp assembly by turning it counterclockwise
- Disconnect the headlamp bulb socket-connector.
- Reinstall in the reverse order of removal.
Information
The headlamp aiming should be adjusted after an accident or after the headlamp assembly is reinstalled at an authorized HYUNDAI dealer.
WARNING
Halogen bulb
- Handle halogen bulbs with care. Halogen bulbs contain pressurized gas that will produce flying pieces of glass that could cause injuries if broken.
- Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
• Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids.
• Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
• A bulb should be operated only when installed in a headlamp.
• If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.
Headlamp (Low/High) and Daytime Running Light (DRL)/Position lamp
If the lamp (LED) does not operate, have the system checked by an authorized HYUNDAI dealer. The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit. A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.
Turn signal lamp
- Open the hood.
- Disconnect the negative battery cable.
- Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
- Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
- Install a new bulb by inserting it into the socket and rotating it until it locks into place.
- Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
- Push the socket into the assembly and turn the socket clockwise.
Side repeater lamp replacement
If the LED lamp (1) does not operate, have the system checked by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.
Rear combination lamp bulb replacement
(1) Stop/Tail lamp
(2) Stop/Tail lamp
(3) Turn signal lamp
(4) Backup lamp
(5) Side marker
Stop/tail lamp and side marker
If the lamp (LED) does not operate, have the system checked by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.
Turn signal lamp and backup lamp
If the lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.
High mounted stop lamp replacement
If the LED lamp (1) does not operate, have the system checked by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.
License Plate Light Bulb Replacement
- Loosen the lens retaining screws with a cross-tip screwdriver.
- Remove the lens.
- Remove the socket by turning it counterclockwise.
- Remove the bulb by pulling it straight out.
- Install a new bulb.
- Reinstall in the reverse order.
Interior Light Bulb Replacement
Map lamp, room lamp and luggage compartment lamp (LED type)
If the lamp (LED) does not operate, have the system checked by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps has to be replaced with the unit.
A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.
Map lamp, room lamp, vanity mirror lamp and luggage compartment lamp (Bulb type)
- Using a flat-blade screwdriver, gently pry the lens from the interior lamp housing.
- Remove the bulb by pulling it straight out.
- Install a new bulb in the socket.
- Align the lens tabs with the interior lamp housing notches and snap the lens into place.
WARNING
Prior to working on the Interior Lights, ensure that the lamp is off to avoid burning your fingers or receiving an electric shock.
NOTICE
Use care not to dirty or damage lens, lens tab, and plastic housings.
Download Manual