Headlight, Position Lamp, Turn Signal Lamp and Daytime Running Light Bulb Replacement
Type A
(1) Turn signal lamp
(2) Headlamp (High/Low)
(3) Daytime running light (if equipped) / Position lamp (LED)
(4) Side marker
WARNING
- Handle halogen bulbs with care. Halogen bulbs contain pressurized gas that will produce flying pieces of glass that could cause injuries if broken.
- Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
- Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids.
- Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
- A bulb should be operated only when installed in a headlamp.
- If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.
Headlamp
1. Open the hood.
2. Disconnect the negative battery cable.
3. Remove the bulb cover (1) by turning it counterclockwise.
4. Remove the wheel guard cover on the back of the bulb.
5. Disconnect the bulb socketconnector. (for low beam and high beam)
6. Remove the bulb from the headlamp assembly.
7. Install a new bulb.
8. Connect the bulb socket-connector. (for low beam and high beam)
9. Install the bulb cover by turning it clockwise.
Turn signal lamp
1. Open the hood.
2. Disconnect the negative battery cable.
3. Remove the bulb cover (2) by turning it counterclockwise.
4. Disconnect the bulb socketconnector.
5. Remove the bulb from the assembly.
6. Install a new bulb.
7. Connect the bulb socket-connector.
8. Install the bulb cover by turning it clockwise.
Daytime running lamp, position lamp and side marker
If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.
Type B
(1) Headlamp (High) (LED)
(2) Headlamp (Low) (LED)
(3) Daytime running light / Position lamp/ Turn signal lamp (LED) (if equipped)
(4) Front fog lamp (if equipped)
(5) Side marker
(6) Side reflex reflector
WARNING
- Handle halogen bulbs with care. Halogen bulbs contain pressurized gas that will produce flying pieces of glass that could cause injuries if broken.
- Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
- Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids.
- Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
- A bulb should be operated only when installed in a headlamp.
- If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.
Headlamp, Daytime running lamp, position lamp, turn signal lamp and side maker
If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.
Side repeater lamp replacement
If the light bulb does not operate, have the vehicle checked by an authorized HYUNDAI dealer.
Rear combination lamp bulb replacement
(1) Stop/Tail lamp
(2) Tail lamp(Type A), Stop/Tail lamp (Type B)
(3) Turn signal lamp (Bulb) (Type A) Turn signal lamp (LED) (Type B)
(4) Reverse lamp
(5) Side marker
Stop/Trial lamp
1. Turn off the engine.
2. Open the tailgate.
3. Loosen the lamp assembly retaining screws with a cross-tip screwdriver.
4. Remove the rear combination lamp assembly from the body of the vehicle.
5. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
6. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
8. Install the socket into the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.
9. Reinstall the lamp assembly to the body of the vehicle.
Trial lamp (Type A)
1. Turn off the engine.
2. Open the tailgate.
3. Remove the service cover using a flatblade screwdriver.
4. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
5. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
6. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
7. Install the socket into the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.
8. Reinstall the lamp assembly to the body of the vehicle.
Tail / Stop lamp and side marker (Type B)
If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.
Turn signal lamp / Reverse lamp
If these lamps do not operate, have the vehicle checked by an authorized HYUNDAI dealer.
High mounted stop lamp replacement
If the high mounted stop lamp (LED) does not operate, contact an authorized HYUNDAI dealer.
License Plate Light Bulb Replacement
1. Using a flat-blade screwdriver, gently pry the lens cover from the lamp housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb.
4. Reinstall in the reverse order.
Interior Light Bulb Replacement
Map lamp, room lamp and luggage compartment lamp (LED type)
If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.
Map lamp, room lamp, vanity mirror lamp and luggage compartment lamp (Bulb type)
1. Using a flat-blade screwdriver, gently pry the lens from the interior lamp housing.
2. Remove the bulb by pulling it straight out.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior lamp housing notches and snap the lens into place.
NOTICE
Use care not to dirty or damage lens, lens tab, and plastic housings.
Download Manual