Smart High Beam (if equipped)
The Smart High Beam is a system that automatically adjusts the headlamp range (switches between high beam and low beam) according to the brightness of other vehicles and road conditions.
Operating condition
1. Place the light switch in the AUTO position.
2. Turn on the high beam by pushing the lever away from you. The smart high beam indicator will illuminate.
3. The Smart High Beam will turn on when vehicle speed is above 28 mph (45km/h).
• If the lever is pushed away when the Smart High Beam is operating, the Smart High Beam will turn off and the high beam will be on continuously. The smart high beam indicator will turn off.
• If the lever is pulled towards you when the Smart High Beam is operating, the Smart High Beam will turn off.
4. If the light switch is placed to the headlamp position, the Smart High Beam will turn off and the low beam will be on continuously.
The high beam switches to low beam in the below conditions.
- When the Smart High Beam is off.
- When the light switch is not in the AUTO position.
- When the headlamp is detected from the on-coming vehicle.
- When the tail lamp is detected from the front vehicle.
- When the surrounding is bright enough high beams are not needed.
- When streetlights or other lights are detected.
- When vehicle speed is below 22 mph (35km/h).
CAUTION
The system may not operate normally in the below conditions.
• When the light from the oncoming or front vehicle is not detected because of lamp damage, hidden from sight, etc.
• When the lamp of the on-coming or front vehicle is covered with dust, snow or water.
• When the light from the oncoming or front vehicle is not detected because of exhaust fume, smoke, fog, snow, etc.
• When the front window is covered with foreign matters such as ice, dust, fog, or is damaged.
• When there is a similar shape lamp with the front vehicle’s lamps.
• When it is hard to see because of fog, heavy rain or snow.
• When the headlamp is not repaired or replaced at an authorized dealer.
• When headlamp aiming is not properly adjusted.
• When driving on a narrow curved road or rough road.
• When driving downhill or uphill.
• When only part of the vehicle in front is visible on a crossroad or curved road.
• When there is a traffic light, reflecting sign, flashing sign or mirror.
• When the road conditions are bad such as being wet or covered with snow.
• When the front vehicle’s headlamps are off but the fog lamps on.
• When a vehicle suddenly appears from a curve.
• When the vehicle is tilted from a flat tire or being towed.
• When the LKAS (Lane keeping Assist System) warning light illuminates. (if equipped)
WARNING
• Do not place any accessories, stickers or tint the windshield.
• Have the windshield glass replaced from an authorized dealer.
• Do not remove or impact related parts of the Smart High Beam system.
• Be careful that water doesn’t get into the Smart High Beam unit.
• Do not place objects on the dashboard that reflects light such as mirrors, white paper, etc. The system may malfunction if sunlight is reflected.
• At times, the Smart High Beam system may not work properly, always check the road conditions for your safety. When the system does not operate normally, manually change between the high beam and low beam.
Turn signals and lane change signals
To signal a turn, push down on the lever for a left turn or up for a right turn in position (A). To signal a lane change, move the turn signal lever slightly and hold it in position (B).The lever will return to the OFF position when released or when the turn is completed.
If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement.
Onetouch turn signal function (if equipped)
To activate an One Touch Turn Signal function, move the turn signal lever slightly and then release it. The lane change signals will blink 3, 5 or 7 times.
You can activate or deactivate the One Touch Turn Signal function or choose the number of blinking (3, 5, or 7) from the User Settings Mode (Light) on the LCD display.
Front fog lamp (if equipped)
Use the switch next to the headlamp switch to turn the Fog Lights ON and OFF. The fog lamps will turn on when the fog lamp switch (1) is turned to the ON position after the headlamps are turned on.
To turn off the fog lamps, turn the switch to the OFF position.
You can use the fog lamps only when the headlamps are on low beam. When the light switch is in the AUTO position, you can also use the fog lamps when the headlamps turn on automatically. The fog lamps will go OFF when the headlamps turn OFF.
✽ NOTICE
When in operation, the fog lamps consume large amounts of vehicle electrical power. Only use the fog lamps when visibility is poor.
Battery saver function
The purpose of this feature is to prevent the battery from being discharged. The system automatically turns off the parking lamp when the driver turns the engine off and opens the driver-side door.
With this feature, the parking lamps will turn off automatically if the driver parks on the side of road at night. If necessary, to keep the lamps on when the engine is turned off, perform the following:
1) Open the driver-side door.
2) Turn the parking lamps OFF and ON again using the light switch on the steering column.
Headlamp delay function (if equipped)
If you place the Engine Start/Stop button in to the ACC or OFF position with the headlamps ON, the headlamps (and/or parking lamps) remain on for about 5 minutes. However, with the engine off if the driver’s door is opened and closed, the headlamps (and/or parking lamps) are turned off after 15 seconds.
The headlamps (and/or parking lamps) can be turned off by pressing the lock button on the smart key twice or turning the light switch to the OFF or AUTO position. However, if you turn the light switch to the AUTO position when it is dark outside, the headlamps will not be turned off. You can activate or deactivate the Headlamp Delay function from the User Settings Mode (Light) on the LCD display.
✽ NOTICE
If the driver gets out of the vehicle through other doors (except driver's door), the battery saver function does not operate and the headlamp delay function does not turn off automatically. Therefore, It causes the battery to be discharged. In this case, make sure to turn off the lamp before getting out of the vehicle.
Daytime running light (DRL) (if equipped)
The Daytime Running Lights (DRL) can make it easier for others to see the front of your vehicle during the day, especially after dawn and before sunset.
for U.S.A
The DRL will turn off when:
- The light switch is not in the AUTO position.
- The parking brake is applied.
- The engine is turned off.
- The hazard warning flasher is on.
- You turn the turn signal light on.
- If you turn on the turn signal light, only the corresponding daytime running lights will turn off.
for Canada
The DRL will turn off when:
- The light switch is in the headlamp position, including the operation that the headlamp is turned on automatically in the AUTO light position.
- The parking brake is applied.
- The engine is turned off.
- The hazard warning flasher is on.
- You turn the turn signal light on.
- If you turn on the turn signal light, only the corresponding daytime running lights will turn off.
- If you turn on turn signal light with the position light turned on, the daytime running lights will turn off but the position light remains on.
Headlamp leveling device (if equipped)
Automatically adjusts the headlamp beam level according to the number of passengers and loading weight in the luggage area.
If the Headlight Leveling Device is not working properly have your vehicle inspected by an authorized HYUNDAI dealer.
Headlamp washer (if equipped)
Washer fluid will be sprayed on the headlamps at the same time you operate the windshield washer when:
- The Engine Start/Stop button is in the ON position.
- The light switch is in the headlamp position (low beam).
✽ NOTICE
- Check the headlamp washers periodically to confirm that the washer fluid is being sprayed properly onto the headlamp lenses.
- The headlamp washer can be operated 15 minutes after the last operation.
Download Manual