Replacing Light Bulbs
Headlight Bulbs
When replacing, use the following bulbs.
High beam headlight: 60 W (HB3 for halogen bulb type)
Low beam headlight: LED type (55 W (H11 for halogen bulb type)
High Beam Headlights
Driver side
- Remove the engine compartment cover.
- Remove the clips.
- Remove the air intake duct.
Both sides - Push the tab to remove the coupler.
- Rotate the old bulb counter-clockwise to remove.
- Insert a new bulb into the headlight assembly and turn it clockwise.
- Insert the coupler into the connector of the bulb.
NOTICE
Halogen bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.
The headlight aim is set by the factory, and does not need to be adjusted. However, if you regularly carry heavy items in the cargo area or tow a trailer, have the aiming readjusted at a dealer or by a qualified technician.
When replacing a halogen bulb, handle it by its base, and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.
Remove the clip using a Phillips-head screwdriver.
Insert the clip with the center pin raised, and push until it is flat.
Low Beam Headlights
1. Push the tab to remove the coupler.
2. Rotate the old bulb counter-clockwise to remove.
3. Insert a new bulb into the headlight assembly and turn it clockwise.
4. Insert the coupler into the connector of the bulb.
Daytime Running Lights and Parking Light Bulbs
Models with LED parking lights
Daytime running lights and parking lights are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
Models without LED parking lights
Daytime running light bulbs and high beam headlight bulbs are the same.
Parking light bulbs and front turn signal bulbs are the same.
Front Side Marker Lights
Front side marker lights are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
Fog Lights
Fog lights are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
Front Turn Signal/Parking* and Fog Light Bulbs
When replacing, use the following bulbs.
Front Turn Signal/Parking* Light: 28/8W (Amber)
Fog Light: 35 W (H8 for halogen bulb type)
- Remove the clip using a flat-tip screwdriver, remove the bolt, and push up the under cover.
- Remove the coupler.
- Turn the socket counter-clockwise and remove it.
- Remove the old bulb and insert a new bulb.
Insert a flat-tip screwdriver, lift and remove the center pin to remove the clip.
Insert the clip with the center pin raised, and push until it is flat.
Side Turn Signal/Emergency Indicator Lights*
Door mirror side turn lights are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
* Not available on all models
Rear Turn Signal and Back-Up Light Bulbs
When replacing, use the following bulbs.
Back-Up Light: 21 W
Rear Turn Signal Light: 21 W
- Use a phillips-head screwdriver to remove the screws.
- Pull the light assembly out of the rear pillar.
- Turn the socket counter-clockwise and remove it. Remove the old bulb.
- Insert a new bulb and turn clockwise.
- Slide the light assembly onto the guide on the body.
- Align the pins with the body grommets, then push in until they fully seat.
Brake/Taillight and Rear Side Marker Lights
Brake/taillight and rear side marker lights are LED type. Have an authorized Honda dealer inspect and replace the light assembly.
Rear License Plate Light Bulbs
When replacing, use the following bulbs.
Rear License Plate Lights: 5 W
- Remove the license plate light assembly by pulling it towards you, and then pulling the front edge upward.
- Turn the socket counter-clockwise and remove it. Remove the old bulb.
- Insert a new bulb and turn clockwise.
High-Mount Brake Light
High-mount brake light is LED type. Have an authorized Honda dealer inspect and replace the light assembly