Bulb Replacement
Headlight (Halogen)/Front Park and Turn Lights
CAUTION!
This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result.
1. Open the hood
2. Remove the two bolts from the front of the headlight housing.
Front Headlight Housing Bolts
3. Remove the plug from the inner fender well and remove the nut through the access hole.
Inner Fender Plug
Rear Headlight Housing Nut Access
4. Pull the housing out from the fender to allow room to disconnect the electrical connectors.
NOTE: For easier removal, pull the headlight assembly straight forward, applying the greatest amount of force to the outer edge of the headlight assembly
Headlight Removal
Bulb Removal
5. Unlock and pull the connector straight from the base of the headlight halogen bulb.
6. Twist the connector on the side marker/turn signal/ park light bulb 1⁄4 turn and remove the connector and bulb from housing.
7. Remove the housing from vehicle with the headlight halogen bulb in housing.
8. Twist the headlight halogen bulb 1⁄4 turn and remove the headlight bulb from the housing.
9. Replace headlight or side marker/turn signal/park light bulb. Do not touch the headlight halogen bulb.
10. Reverse the procedure for installation of bulbs and housing.
Fog Lights
1. Reach under the vehicle, unlock and twist the connector counterclockwise 1⁄4 turn and remove the connector and bulb from the housing.
2. Pull the bulb straight from the connector.
3. Reverse the procedure for installation of the bulbs and housing.
Tail, Stop, Turn and Backup Lights
1. Remove the two screws that pass through the bed sheetmetal.
Removing The Two Screws
2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged.
Pulling Housing From Body
3. Rotate the bulb socket counterclockwise to remove from the housing.
Rotating Bulb Socket From Housing
4. Pull the bulb straight out of socket.
Pulling Bulb From Socket
5. Reverse the procedure to install the bulb and housing. Place the two raised blocks past the body.
Sliding Raised Blocks Past Body
Center High-Mounted Stoplight (CHMSL) With Cargo Light
1. Remove the two screws holding the housing/lens to the body as shown.
2. Separate the connector holding the housing and wiring harness to the body.
3. Turn the desired bulb socket 1⁄4 turn and remove the socket and bulb from housing.
4. Pull the desired bulb straight from the socket.
- Outside Bulbs: Cargo Lights
- Inside Bulb: Center High-Mounted Stop Light
5. Reverse the procedure for installation of the bulbs and housing.
Cab Top Clearance Lights — If Equipped
1. Remove the two screws from the top of the light.
2. Rotate the socket 1⁄4 turn and pull it from the light assembly
3. Pull the bulb straight from it’s socket and replace.
Tailgate ID Lights (Dual Rear Wheels) — If Equipped
1. Remove the two screws and housing and access the bulb sockets from the rear.
2. Turn the socket 1⁄4 turn counterclockwise to access the bulb.
3. Pull the bulb straight out from socket.
4. Reverse the procedure for installation of the bulbs and housing.
Rear Light Bar ID Marker (Dual Rear Wheel) — If Equipped
1. Loosen the two screws and the housing to gain access to the bulb sockets.
2. Turn the socket 1⁄4 turn counterclockwise to access the bulb.
3. Pull the bulb straight out from the socket.
4. Reverse the procedure for installation of the bulbs and housing.
Side Marker Lights (Dual Rear Wheels)
1. Push rearward on the side marker light assembly.
2. Pull the entire assembly from the fender.
3. Turn the socket 1⁄4 turn counterclockwise and remove from assembly to access the bulb.
4. Pull the bulb straight out from socket.
5. Reverse the procedure for installation of the bulbs and housing.