Exterior Lighting
Exterior Lamp Controls
The exterior lamp control is on the instrument panel to the left of the steering column.
There are four positions:
: Turns the exterior lamps off and deactivates the AUTO mode. Turn again to reactivate the AUTO mode.
In Canada, the headlamps will automatically reactivate when the vehicle is shifted out of P (Park).
AUTO : Turns the exterior lamps on and off automatically depending on outside lighting
: Turns on the parking lamps including all lamps, except the headlamps.
: Turns on the headlamps together with the parking lamps and instrument panel lights. A warning chime sounds if the driver door is opened when the ignition is off and the headlamps are on.
IntelliBeam® System
If equipped, this system turns the vehicle's high-beam headlamps on and off according to surrounding traffic conditions.
The system turns the high-beam headlamps on when it is dark enough and there is no other traffic present.
This light comes on in the instrument cluster when the IntelliBeam system is enabled.
Turning On and Enabling IntelliBeam
To enable the IntelliBeam system, press bon the turn signal lever when it is dark outside and the exterior lamp control is in AUTO or 5. The blue high-beam on light appears on the instrument cluster when the high beams are on.
Driving with IntelliBeam
The system only activates the high beams when driving over 40 km/h (25 mph).
There is a sensor near the top center of the windshield that automatically controls the system. Keep this area of the windshield clear of debris to allow for best system performance.
The high-beam headlamps remain on, under the automatic control, until one of the following situations occurs:
- The system detects an approaching vehicle's headlamps.
- The system detects a preceding vehicle's taillamps.
- The outside light is bright enough that high-beam headlamps are not required.
- The vehicle's speed drops below 20 km/h (12 mph).
- The IntelliBeam system is disabled by the button on the turn signal lever. If this happens, pressbon the turn signal lever when the exterior lamp control is in the AUTO or 5 position to reactivate the IntelliBeam system. The instrument cluster light will come on to indicate the IntelliBeam system is reactivated.
The high beams may not turn off automatically if the system cannot detect another vehicle's lamps because of any of the following:
- The other vehicle's lamps are missing, damaged, obstructed from view, or otherwise undetected.
- The other vehicle's lamps are covered with dirt, snow, and/or road spray.
- The other vehicle's lamps cannot be detected due to dense exhaust, smoke, fog, snow, road spray, mist, or other airborne obstructions.
- The vehicle's windshield is dirty, cracked, or obstructed by something that blocks the view of the light sensor.
- The vehicle is loaded such that the front end points upward, causing the light sensor to aim high and not detect headlamps and taillamps.
- The vehicle is being driven on winding or hilly roads.
The IntelliBeam system may need to be disabled if any of the above conditions exist.
Headlamp High/Low-Beam Changer
Push the turn signal lever away from you and release, to turn the high beams on. To return to low beams, push the lever again or pull it toward you and release.
This indicator light turns on in the instrument cluster when the high-beam headlamps are on.
Flash-to-Pass
To flash the high beams, pull the turn signal lever all the way toward you. Then release it.
Daytime Running Lamps (DRL)
Daytime Running Lamps can make it easier for others to see the front of your vehicle during the day. Fully functional DRL are required on all vehicles first sold in Canada.
A light sensor on top of the instrument panel makes the DRL work, so be sure it is not covered.
The DRL system makes the low-beam headlamps come on at a reduced brightness when the following conditions are met:
- The ignition is on.
- The exterior lamp control is in AUTO.
- The engine is running.
When the DRL are on, the taillamps, sidemarker, instrument panel, and other lamps will not be on.
The headlamps automatically change from DRL to the regular headlamps depending on the darkness of the surroundings. The other lamps that come on with the headlamps will also come on.
When it is bright enough outside, the headlamps go off and the DRL come on.
The DRL turn off when the headlamps are turned to 
or the ignition is off. For vehicles first sold in Canada, this control only works when the vehicle is parked.
Automatic Headlamp System
When it is dark enough outside and the exterior lamp control is in the automatic position, the headlamps come on automatically. See Exterior Lamp Controls.
The vehicle has a light sensor on top of the instrument panel. Make sure it is not covered, or the headlamps will be on when they are not needed.
The system may also turn on the headlamps when driving through a parking garage or tunnel.
If the vehicle is started in a dark garage, the automatic headlamp system comes on immediately. If it is light outside when the vehicle leaves the garage, there is a slight delay before the automatic headlamp system changes to the DRL. During that delay, the instrument cluster may not be as bright as usual. Make sure the instrument panel brightness control is in the full bright position.
Lights On with Wipers
If the windshield wipers are activated in daylight with the engine on, and the exterior lamp control is in AUTO, the headlamps, parking lamps, and other exterior lamps come on. The transition time for the lamps coming on varies based on wiper speed. When the wipers are not operating, these lamps turn off. Move the exterior lamp control to 
or 
to disable this feature.
Hazard Warning Flashers
Press and momentarily hold to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press and momentarily hold again to turn the flashers off.
Turn and Lane-Change Signals
Move the lever all the way up or down to signal a turn.
An arrow on the instrument cluster will flash in the direction of the turn or lane change.
Raise or lower the lever until the arrow starts to flash to signal a lane change. The turn signal flashes three times.
The lever returns to its starting position when it is released.
If after signaling a turn or lane change the arrow flashes rapidly or does not come on, a signal bulb may be burned out. Replace any burned out bulbs. If a bulb is not burned out, check the fuse.
Fog Lamps
The fog lamps button is on the instrument panel beside the steering wheel.
To turn on the fog lamps, the ignition and the headlamps or parking lamps must be on.
If equipped, press to turn on or off. An indicator light on the instrument cluster comes on when the fog lamps are on.
Some localities have laws that require the headlamps to be on along with the fog lamps.
Download Manual