2020 Dodge Charger Owners Manual - REMOTE START — IF EQUIPPED

REMOTE START — IF EQUIPPED

HOW TO USE REMOTE START — IF EQUIPPED

Push remote start button on the key fob twice within five seconds. Pushing the remote start button a third time shuts the engine off.

To drive the vehicle, push the unlock button, and place the ignition in the ON/RUN position.

With remote start, the engine will only run for 15 minutes (timeout) unless the ignition is placed in the ON/RUN position.

The vehicle must be started using the key fob after two consecutive timeouts.

All of the following conditions must be met before the engine will remote start:

Gear selector in PARK

Doors closed

Hood closed

Trunk closed

Hazard switch off

Brake switch inactive (brake pedal not pushed)

Battery at an acceptable charge level

Check engine light shall not be present

PANIC button not pushed

System not disabled from previous remote start event

Vehicle alarm system indicator flashing

Ignition in the STOP/OFF position

Fuel level meets minimum requirement

Vehicle security alarm is not signaling an intrusion

(Continued)

The following messages will display in the instrument cluster display if the vehicle fails to remote start or exits remote start prematurely:

Remote Start Aborted — Door Open

Remote Start Aborted — Hood Open

Remote Start Aborted — Fuel Low

Remote Start Aborted — Trunk Open

Remote Start Disabled — Start Vehicle To Reset

The message will stay active until the ignition is placed in the ON/RUN position.

Push and release the remote start button on the key fob twice within five seconds. The vehicle doors will lock, the parking lights will flash, and the horn will chirp twice (if programmed). Then, the engine will start, and the vehicle will remain in the Remote Start mode for a 15 minute cycle.

If an engine fault is present or fuel level is low, the vehicle will start and then shut down in 10 seconds.

The parking lights will turn on and remain on during Remote Start mode.

For security, power window and power sunroof operation (if equipped) are disabled when the vehicle is in the Remote Start mode.

The engine can be started two consecutive times with the key fob. However, the ignition must be cycled by pushing the START/STOP ignition button twice (or the ignition switch must be placed in the ON/RUN position) before you can repeat the start sequence for a third cycle.

Push and release the remote start button one time or allow the engine to run for the entire 15 minute cycle.

To avoid unintentional shutdowns, the system will disable for two seconds after receiving a valid remote start request.

Before the end of 15 minute cycle, push and release the unlock button on the key fob to unlock the doors and disarm the vehicle security alarm (if equipped). Then, prior to the end of the 15 minute cycle, push and release the START/STOP ignition button.

For vehicles not equipped with the Keyless Enter-N-Go — Passive Entry feature, the igni- tion switch must be in the ON/RUN position in order to drive the vehicle.

For vehicles equipped with the Keyless

Enter-N-Go — Passive Entry feature, the message“Remote Start Active — Push Start Button” will show in the instrument cluster display until you push the START/STOP ignition button.

2

Remote Starting will also cancel if any of the following occur:

The engine stalls or engine speed exceeds 2500 RPM.

Any engine warning lights come on.

Low Fuel Light turns on.

The hood is opened.

The hazard switch is pushed.

The gear selector is moved out of PARK.

The brake pedal is pushed.

When remote start is activated, the heated steering wheel and driver heated seat features will automatically turn on in cold weather. In warm weather, the driver vented seat feature

will automatically turn on when the remote start is activated. These features will stay on through the duration of remote start or until the ignition switch is placed in the ON/RUN position.

The following regulatory statement applies to all Radio Frequency (RF) devices equipped in this vehicle:

This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

This device may not cause harmful interference, and

This device must accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d`Innovation, Science and Economic Development applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

l'appareil ne doit pas produire de brouillage, et

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compro- mettre le fonctionnement.

La operación de este equipo está sujeta a las siguientes dos condiciones:

es posible que este equipo o dispositivo no cause interferencia perjudicial y

este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.

Changes or modifications not expressly approved by the party responsible for compli- ance could void the user’s authority to operate the equipment.