Seats
E68595
When you use them properly, the seat, head restraint, seatbelt and airbags will provide optimum protection in the event of a crash.
We recommend that you follow these guidelines:
(25 cm) between your breastbone and the airbag cover.
Make sure that your driving position is comfortable and that you can maintain full control of your vehicle.
151
The head restraints may consist of:
Note: Adjust the seat backrest to an upright
driving position before adjusting the head restraint. Adjust the head restraint so that the top of it is level with the top of your head and as far forward as possible. Make sure that you remain comfortable. If you are extremely tall, adjust the head restraint to its highest position.
E138642
Adjusting the Head Restraint
Raising the Head Restraint
Pull the head restraint up.
Align the steel stems into the guide sleeves and push the head restraint down until it locks.
Your vehicle may have head restraints that are non-adjustable. The non-adjustable head restraints consist of:
E153105
152
E162872
A
B C
An energy absorbing head restraint.
Two steel stems.
Guide sleeve unlock and remove button.
E144727
Align the steel stems into the guide sleeves and push the head restraint down until it locks.
Your vehicle may have a front row center head restraint that you cannot adjust or remove.
The front head restraints tilt for extra comfort.
your head to the desired position.
After the head restraint reaches the forward-most tilt position, pivot it forward again to release it to the rearward, un-tilted position.
Note: Do not attempt to force the head restraint backward after you tilt it. Instead, continue tilting it forward until the head restraint releases to the upright position.
MANUAL SEATS (IF EQUIPPED)
|
|
WARNING: Do not adjust the driver's seat or seatback when your vehicle is moving.153
Moving the Seat Backward and Forward
E175314
E175315
154
Manual Lumbar (If Equipped)
E166702
The lumbar support control is located on the outboard side of the seat. Turn the control to adjust your support.
POWER SEATS (IF EQUIPPED)
|
|
WARNING: Do not adjust the driver seat or seat backrest when your vehicle is moving. This may result in sudden seat movement, causing the loss of control of your vehicle.
WARNING: Do not place cargo or any objects behind the seatback before returning it to the original position.E176038
Adjusting the Lumbar Support (If Equipped)
Note: The engine must be running or the vehicle must be in accessory mode to activate the seats.
Note: Allow a few seconds for any selection to activate. When the seat backrest and cushion are both active, the massage alternates between zones.
155
|
Massage Mode |
Lumbar and Bolster Mode |
|
|
A |
Back massage intensity adjustment |
Upper lumbar |
|
B |
Massage intensity decrease and off* |
Lumbar decrease |
|
C |
Cushion massage intensity adjustment |
Lower lumbar** |
|
D |
Massage intensity increase |
Lumbar increase |
|
E |
On and off |
- |
*The massage feature defaults to an
alternating massage mode with back massage intensity adjustment. The lumbar and bolster feature defaults to the middle lumbar mode.
**Press C a second time to adjust the back bolster. Press C a third time to adjust the cushion bolster.
You can also adjust this feature through the touchscreen. When switched on, the system displays directions for you to adjust the lumbar settings in your seat or to set the massage function.
To access and make adjustments to the lumbar setting:
> Multi-Contour Seat.
To access and make adjustments to the massage setting:
>Multi-Contour Seat.
156
|
|
WARNING: Before activating the memory seat, make sure that the area immediately surrounding the seat is clear of obstructions and that all occupants are clear of moving parts.
WARNING: Do not use the memory function when your vehicle is moving.This feature recalls the position of the following:
E307868
Note: A confirmation that you saved a memory preset appears in the information display.
Note: You can save up to three preset memory positions.
Note: You can save a memory preset at any time.
Note: You can only recall preset memory positions when you switch the ignition off, or when the transmission is in park (P) or neutral (N) if you switch the ignition on.
You can also recall a preset memory position by:
Note: Using a linked key fob to recall your memory position when the ignition is off moves the seat and steering column to the easy entry position.
Note: Pressing any active memory feature control - power seat, mirror (or any memory button) during a memory recall cancels the operation.
Your vehicle can save the preset memory positions for up to two remote controls.
157
3. Within ten seconds, press the lock button on the remote control you are linking. The instrument panel indicates a successful link.
To unlink a remote control, follow the same procedure – except in step 3, press the unlock button on the remote control.
Note: If more than one linked remote control or intelligent access key is in range, the memory function moves to the settings of the first key to initiate a memory recall.
Easy Entry and Exit Feature (If Equipped)
If you enable the easy entry and exit feature, it moves the driver seat rearward up to 2 in (5 cm) when you put the transmission in park (P) and remove the key from the ignition.
The driver seat returns to the previous position when you put the key in the ignition.
You can enable or disable this feature through the information display. See Information Displays (page 110).
REAR SEATS (IF EQUIPPED)
If your vehicle has a 60/40 rear seat, you can flip each cushion up into a vertical storage position.
Rotate the seat cushion up until it locks into the vertical storage position.
The locking key is in the remote control. See Remote Control (page 55).
Turn the key to lock or unlock.
158
|
|
WARNING: Check under the seat cushion to make sure no cargo or objects are under the seat cushion before returning the seat cushion to its original position, and that the seat cushion locks into place. Failure to do so may prevent the seat from operating properly in the event of a crash, which could increase the risk of serious injury.Lift the lever and flip up the seat cushion to access the storage space and the power point (A).
E162740
To remove the storage space divider, squeeze the sides and lift it from the storage tub.
Pull the strap to release the seat cushion from the storage position.
The rear seat has storage space under the seat cushion.
159
Use your vehicle key to lock the storage space. See Keys and Remote Controls (page 55).
HEATED SEATS (IF EQUIPPED)
|
|
WARNING: People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the heated seat to overheat. Do not puncture the seat with pins, needles or other pointed objects. This may damage the heating element which may cause the heated seat to overheat. An overheated seat may cause serious personal injury.Do not do the following:
• Place heavy objects on the seat.
• Operate the heated seat if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.
Note: The engine must be running to use this feature.
E146322
Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings.
Note: The heated seats may remain on after you remote start your vehicle, based on your remote start settings. The heated seats may also turn on when you start your vehicle if they were on when you switched your vehicle off.
|
|
WARNING: People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the heated seat to overheat. Do not puncture the seat with pins, needles or other pointed objects. This may damage the heating element which may cause the heated seat to overheat. An overheated seat may cause serious personal injury.Do not do the following:
• Place heavy objects on the seat.
• Operate the heated seat if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.
Note: The engine must be running to use this feature.
The rear seat heat controls are on the rear of the center console.
160
E146322
Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings.
The heated seat module resets at every ignition run cycle. While the ignition is in the on position, press the heated seat switch to enable heating mode. When activated, they turn off automatically when you switch off the engine.
Note: The ventilated seats may remain on after you remote start your vehicle, based on your remote start settings. The ventilated seats may also turn on when you start your vehicle if they were on when you switched your vehicle off.
Do not do the following:
The engine must be running to use this feature.
Press this symbol to cycle through the various ventilation settings and off. More indicator lights indicate higher fan speeds.
If the engine falls below 350 RPM while the ventilated seats are on, the feature turns itself off. You need to reactivate it.
Note: To improve comfort, use the ventilated seats along with the vehicle’s air conditioning system.
E224689
161
Download Manual