Keys and Remote Controls
This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
|
|
WARNING: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met.The typical operating range for your transmitter is approximately 33 ft (10 m). Vehicles with the remote start feature will have a greater range.
One of the following could cause a decrease in operating range:
The radio frequency used by your remote control can also be used by other radio transmitters, for example amateur radios, medical equipment, wireless headphones, wireless remote controls, cell phones, battery chargers and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key.
Note: Make sure to lock your vehicle before leaving it unattended.
Note: If you are in range, the remote control will operate if you press any button unintentionally.
Note: The remote control contains sensitive electrical components. Exposure to moisture or impact may cause permanent damage.
The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met:
If excessive radio frequency interference is present in the area or if the transmitter battery is low, you may need to mechanically unlock your door. You can use the mechanical key blade in your intelligent access key to open the driver door in this situation. See Remote Control (page 55).
Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control.
55
E191532
Press the button to release the key blade. Press and hold the button to fold the key blade back in when not in use.
E151795
Note: Your vehicle keys came with a security label that provides important key cut information. Keep the label in a safe place for future reference.
Note: You may not be able to shift out of park (P) unless the intelligent access key is inside your vehicle.
E307113
The intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to use the push button start.
The intelligent access key also contains a removable key blade that you can use to unlock your vehicle.
56
|
|
WARNING: If the battery compartment does not securely close, stop using the remote control and replace it as soon as possible. In the meantime, keep the remote control away from children. Failure to follow this instruction could result in personal injury or death.E307112
Press the release button and pull the key blade out.
E151795
Note: Your vehicle keys came with a security label that provides important key cut information. Keep the label in a safe place for future reference.
Note: Refer to local regulations when disposing of transmitter batteries.
Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.
Note: Replacing the battery does not erase the programmed key from your vehicle. The transmitter should operate normally.
A message appears in the information display when the remote control battery is low. See General Information (page 110).
The remote control uses one coin-type three-volt lithium battery CR2032 or equivalent.
Press the button to release the key blade before beginning the procedure.
57
E151801
The remote control uses one coin-type three-volt lithium battery CR2450 or equivalent.
E151800
Note: Do not touch the battery contacts or the printed circuit board with the screwdriver.
58
E303824
E218402
You can use the remote control to recall memory positions.
Press the unlock button on a linked remote control to recall memory positions. If you enable the easy entry and exit feature, the seat moves to the easy entry position. The seat moves to the driver memory position when you switch the ignition on.
See Memory Function (page 157).
59
Press the button twice within three seconds. A tone sounds and the direction indicators
flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm.
Press the button to sound the panic alarm. Press the button again or switch the ignition on to
turn it off.
Note: The panic alarm only operates when the ignition is off.
Replacement keys or remote controls can be purchased from an authorized dealer. Authorized dealers can program remote controls for your vehicle.
60
Download Manual