Security
Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in engine starting problems and a loss of security protection.
Note: Metallic objects, electronic devices or a second coded key on the same key chain may result in vehicle starting problems, especially if they are too close to the key when starting your vehicle. Prevent these objects from touching the coded key when starting your vehicle. Switch the ignition off, move all objects on the key chain away from the coded key and restart your vehicle if a problem occurs.
Note: Do not leave a duplicate coded key in your vehicle. Always take your keys and lock all doors when leaving your vehicle.
The system helps prevent the engine from starting unless you use a coded key programmed to your vehicle. Using the wrong key may prevent your vehicle from starting. A message may appear in the information display.
If you are unable to start your vehicle with a coded key, it is not operating correctly.
A message may appear in the information display.
The system arms when you switch the ignition off.
The system disarms when you switch the ignition on with a coded key.
Note: Your vehicle comes with two keys.
The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts your vehicle, as well as a remote control.
The intelligent access key functions as a programmed key that operates the driver door lock and turns on the intelligent access with push button start system, as well as a remote control.
If your coded keys are lost or stolen and you do not have an extra coded key, you need to erase the key codes from your vehicle and program new coded keys. Contact an authorized dealer.
Store an extra programmed key away from your vehicle in a safe place. You can purchase replacement keys or remote controls from an authorized dealer.
Note: You can program a maximum of four keys to your vehicle. All six can be integrated keyhead transmitters.
You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. This procedure programs both the vehicle immobilizer keycode and the remote control to your vehicle.
Only use integrated keyhead transmitters or standard SecuriLock keys.
You must have two previously programmed coded keys and the new unprogrammed key readily accessible. Contact an authorized dealer to have the spare key programmed if two previously programmed keys are not available.
Read and understand the entire procedure before you begin.
78
If you have successfully programmed the new integrated keyhead transmitter, it will start your vehicle and operate the remote entry system.
If programming was unsuccessful, wait 10 seconds and repeat steps 1 through 9. If you are still unsuccessful, take your vehicle to your authorized dealer.
Note: Do not place the device on the wireless accessory charging area when programming intelligent access keys.
Note: You can program a maximum of six keys to your vehicle. All six must be intelligent access keys.
This procedure programs both the vehicle immobilizer keycode and the remote control to your vehicle.
You must have two previously programmed intelligent access keys inside your vehicle and the new unprogrammed intelligent access key readily accessible. Contact an authorized dealer to have the spare key programmed if two previously programmed keys are not available.
Make sure that the ignition is switched off before beginning this procedure. Make sure that you close all the doors before beginning and that they remain closed throughout the procedure. Carry out all steps within 30 seconds of starting the sequence. Stop and wait for at least one minute before starting again if you carry out any steps out of sequence.
Read and understand the entire procedure before you begin.
79
E226701
Programming is now complete. Check that the remote control functions operate and your vehicle starts with the new intelligent access key.
If programming was unsuccessful, wait 10 seconds and repeat steps 1 through 7. If you are still unsuccessful, take your vehicle to your authorized dealer.
The active anti-theft system is designed to warn you in the event of unauthorized vehicle entry and is also designed to help prevent unwanted towing of your vehicle. You can choose what is monitored by arming the system in different ways. See Information Displays (page 112).
The direction indicators flash and the horn sounds if the system triggers while the alarm is armed.
Take all remote controls to an authorized dealer if there is any potential alarm problem with your vehicle.
80
You can select two levels of alarm security. You can change the level of security when the ignition is switched off through the information display with the two options below:
Perimeter only monitors the following:
All sensors monitors the following:
Note: Do not choose all sensors monitor mode when the vehicle is in transport or if movement within the vehicle is likely to occur.
Note: For correct operation of the interior motion detection system, make sure you close all the windows prior to arming the system. This helps prevent accidental alarm activation due to external influences.
Additionally, the interior motion sensing system does not arm if any door is ajar.
The alarm is ready to arm when there is not a key in the ignition. Lock your vehicle using the remote control or keyless entry keypad. You can also lock your vehicle using the lock sensor on the exterior door handle if your vehicle is equipped with intelligent access. See Locking and Unlocking (page 69).
The direction indicators flash once after you lock your vehicle. This indicates the alarm is in the pre-armed mode. It fully arms after 20 seconds.
Disarm the alarm by any of the following actions:
81
Download Manual