Driving Hints
You need to break in new tires for approximately 300 mi (480 km). During this time, your vehicle may exhibit some unusual driving characteristics.
Avoid driving too fast during the first 1,000 mi (1,600 km). Vary your speed frequently and change up through the gears early. Do not labor the engine.
Drive your new vehicle at least 1,000 mi (1,600 km) before towing a trailer. Make sure you use the specified engine oil. See Capacities and Specifications (page 427).
Do not add friction modifier compounds or special break-in oils during the first few thousand miles (kilometers) of operation. These additives may prevent piston ring seating.
Your fuel economy is affected by several things, such as how you drive, the conditions you drive under, and how you maintain your vehicle.
You may improve your fuel economy by keeping these things in mind:
Accelerate and slow down in a smooth, moderate fashion.
Drive at steady speeds without stopping.
Anticipate stops; slowing down may eliminate the need to stop.
Combine errands and minimize stop-and-go driving.
Close the windows for high-speed driving.
Drive at reasonable speeds (traveling at 55 mph [88 km/h] uses 15% less fuel than traveling at 65 mph [105 km/h]).
Keep the tires properly inflated and use only the recommended size.
Use the recommended engine oil.
Perform all regularly scheduled maintenance.
Avoid these actions; they reduce your fuel economy:
Sudden accelerations or hard accelerations.
Revving the engine before turning it off.
Idle for periods longer than one minute.
Warm up your vehicle on cold mornings.
Use the air conditioner or front defroster.
Use the speed control in hilly terrain.
Rest your foot on the brake pedal while driving.
Drive a heavily loaded vehicle or tow a trailer.
Carry unnecessary weight (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kilogram] of weight carried).
Driving with the wheels out of alignment.
Conditions
Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed.
Adding certain accessories to your vehicle (for example bug deflectors, rollbars, light bars, running boards, ski racks or luggage racks) may reduce fuel economy.
To maximize the fuel economy, drive with the tonneau cover installed (if equipped).
Using fuel blended with alcohol may lower fuel economy.
298
Fuel economy may decrease with lower temperatures during the first 5–10 mi (12–16 km) of driving.
Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal.
Four-wheel-drive operation (if equipped) is less fuel efficient than two-wheel-drive operation.
Close the windows for high-speed driving.
Do not drive through flowing or deep water as you may lose control of your vehicle.
Note: Driving through standing water can cause vehicle damage.
Note: Engine damage can occur if water enters the air filter.
Before driving through standing water, check the depth. Never drive through water that is higher than the bottom of the wheel hubs.
E176913
When driving through standing water, drive very slowly and do not stop your vehicle. Your brake performance and traction may be limited. After driving through water and as soon as it is safe to do so:
Lightly press the brake pedal to dry the brakes and to check that they work.
Check that the horn works.
Check that the exterior lights work.
Turn the steering wheel to check that the steering power assist works.
Use a floor mat designed to fit the footwell of your vehicle that does not obstruct the pedal area. Failure to
follow this instruction could result in the loss of control of your vehicle, personal injury or death.
Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal
injury.
Secure the floor mat to both retention devices so that it cannot slip out of position and interfere with
the pedals. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury or death.
Do not place additional floor mats or any other covering on top of the original floor mats. This could result
in the floor mat interfering with the operation of the pedals. Failure to follow this instruction could result in the loss of control of your vehicle, personal injury or death.
Always make sure that objects cannot fall into the driver foot well while your vehicle is moving. Objects
that are loose can become trapped under the pedals causing a loss of vehicle control.
299
To install the floor mats, position the floor mat eyelet over the retention post and press down to lock in position.
To remove the floor mat, reverse the installation procedure.
Note: Regularly check the floor mats to make sure they are secure.
Ford recommends that the Super Duty F-Series used for snow removal include the snowplow package option.
Weight limits and guidelines for selecting and installing the snowplow are in the Ford Truck Body Builders Layout Book, snowplow section, found at www.fleet.ford.com/truckbbas. A typical installation affects the following:
Certification to government safety laws such as occupant protection and airbag deployment, braking, and lighting. Look for an Alterer’s Label on the vehicle from the snowplow installer certifying that the installation meets all applicable Federal Motor Vehicle Safety Standards (FMVSS).
The Total Accessory Reserve Capacity (TARC) is on the lower right side of the vehicle’s Safety Compliance Certification Label. This applies to Ford-completed vehicles of 10,000 lb (4,536 kg) GVWR or less. This is the weight of permanently-attached auxiliary equipment, such as snowplow frame-mounting hardware, that can be added to the vehicle and satisfy Ford compliance certification to FMVSS. Exceeding this weight may require the auxiliary equipment installer additional safety certification responsibility. The Front Accessory Reserve Capacity (FARC) is for customer convenience.
Rear ballast weight behind the rear axle may be required to prevent exceeding the FGAWR, and provide front-to-rear weight balance for proper braking and steering.
Front wheel toe may require
re-adjustment to prevent premature uneven tire wear. Specifications are in the Ford Workshop Manual.
Headlight aim may require re-adjustment.
300
Note: Do not use your vehicle for snow removal until you have driven at least 500 mi (800 km).
Ford recommends vehicle speed does not exceed 45 mph (72 km/h) when snowplowing.
The attached snowplow blade restricts airflow to the radiator, and may cause the engine to run at a higher temperature: Attention to engine temperature is especially important when outside temperatures are above freezing. Angle the blade to maximize airflow to the radiator and monitor engine temperature to determine whether a left or right angle provides the best performance.
Follow the severe duty schedule in your Scheduled Maintenance information for engine oil and transmission fluid change intervals.
Do not attempt to service, repair, or modify the airbag supplemental restraint system (SRS) or its fuses.
Contact an authorized dealer.
Additional equipment for example snowplow equipment may affect the performance of the airbag sensors
increasing the risk of injury. Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment.
All occupants of the vehicle, including the driver, should always properly wear their seatbelt, even
when provided with an airbag supplemental restraint system (SRS).
Your vehicle is equipped with a driver and passenger airbag supplemental restraint system. The supplemental restraint system will activate in certain frontal and offset frontal collisions when the vehicle sustains sufficient frontal deceleration.
Careless or high speed driving while plowing snow that results in sufficient vehicle decelerations can deploy the airbags. Such driving also increases the risk of accidents.
Never remove or defeat the tripping mechanisms designed into the snow removal equipment by its manufacturer. Doing so may cause damage to the vehicle and the snow removal equipment as well as possible airbag deployment.
When driving with a plow, your engine may run at a higher temperature than normal because the attached snowplow blade will restrict airflow to the radiator.
301
(72 km/h) in cold weather, you will not need to worry about blade position to provide maximum airflow.
Do not spin the wheels at over
34 mph (55 km/h). The tires may fail and injure a passenger or bystander.
Shift transfer case to 4L (4WD Low) when plowing in small areas at speeds below 5 mph (8 km/h).
Shift transfer case to 4H (4WD High) when plowing larger areas or light snow at higher speeds. Do not exceed 15 mph (24 km/h).
Do not shift the transmission from a forward gear to R (Reverse) until the engine is at idle and the wheels have stopped.
302
Download Manual