2022 Toyota Yaris Owners Manual - Light Bulbs

Light Bulbs

Front

With Halogen Headlights

1. Headlights (Low/High beam)/Daytime running lights
2. Front side-marker lights
3. Overhead lights/Map lights
4. Side turn signal lights (if equipped)
5. Front turn signal lights/Parking lights
6. Fog lights (if equipped)

With LED Headlights

1. Headlights (High beam)
2. Headlights (Low beam)
3. Front side-marker lights
4. Overhead lights/Map lights
5. Side turn signal lights (if equipped)
6. Front turn signal lights/Parking lights
7. Daytime running light/Parking light
8. Fog lights

Rear

4-Door

1. Trunk light
2. High-mount brake lights
3. License plate lights
4. Reverse lights
5. Rear turn signal lights
6. Brake lights/Taillights/Rear side-marker lights

5-Door

1. High-mount brake light
2. License plate lights
3. Reverse lights
4. Rear turn signal lights
5. Brake lights/Tail lights
6. Rear side-marker lights
7. Luggage compartment light

• To replace the bulb, contact your Toyota dealer.
• If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.
• Use the protective cover and carton of the replacement bulb to dispose of the old bulb promptly out of the reach of children.

WARNING

Never touch the glass portion of a halogen bulb with your bare hands and always wear eye protection when handling or working around the bulbs

When a halogen bulb breaks, it is dangerous. These bulbs contain pressurized gas. If one is broken, it will explode and serious injuries could be caused by the flying glass.

If the glass portion is touched with bare hands, body oil could cause the bulb to overheat and explode when lit.

Always keep halogen bulbs out of the reach of children

Playing with a halogen bulb is dangerous. Serious injuries could be caused by dropping a halogen bulb or breaking it some other way.

NOTICE

When removing the lens or lamp unit using a flathead screwdriver, make sure that the flathead screwdriver does not contact the interior terminal. If the flathead screwdriver contacts the terminal, a short circuit may occur.

Replacing Exterior Light Bulbs

Headlights/Daytime running lights (With halogen headlights)

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Lift the hood.
3. Disconnect the connector from the bulb.

   

4. Detach the sealing cover from the bulb.

   

   1. Retaining spring
   2. Sealing cover
5. Unhook the bulb retaining spring.
6. Swing the retaining spring out and away to free the headlight bulb.
7. Carefully remove the headlight bulb from the socket by pulling it straight back.
8. Replace the bulb.
9. Install the new bulb in the reverse order of the removal procedure.

Front turn signal lights/Parking lights, Front side-marker lights

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Lift the hood.
3. Front turn signal lights/Parking lights: Remove the fuse block cover.

   

4. Turn the socket and bulb assembly counterclockwise and remove it.
5. Disconnect the bulb from the socket.

   Front turn signal lights/Parking lights

   

   Front side-marker lights

   

6. Install the new bulb in the reverse order of the removal procedure.

Fog lights (if equipped)

1. Make sure the ignition is switched off, and the fog light switch is off.
2. Turn the screws counterclockwise and remove them.

   

3. Pull the center of each retainers and remove them, and then partially peel back the front under cover.

   

   1. Removal
   2. Installation
4. Disconnect the connector from the unit by pressing the tab on the connector with your finger and pulling the connector downward.

   

5. Turn the socket and bulb assembly to remove it. Carefully remove the bulb from its socket in the reflector by gently pulling it straight backward out of the socket.

   

6. Install the new bulb in the reverse order of the removal procedure.

Rear turn signal lights, Brake lights/Taillights/Rear side-marker lights

4-Door

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Remove the cover.

   

3. Turn the socket and bulb assembly counterclockwise and remove it.
4. Disconnect the bulb from the socket.

   Rear turn signal lights:

   

    Brake lights/Taillights/Rear sidemarker lights:

   

5. Install the new bulb in the reverse order of the removal procedure.
6. Insert the cover tabs and install the cover.

   Verify that the cover is securely installed.

5-Door

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Turn the bolts counterclockwise and remove them.

   

3. Pull the unit rearward to remove it.

   

4. Turn the socket and bulb assembly counterclockwise and remove it.
5. Disconnect the bulb from the socket.

   Rear turn signal lights:

   

   Brake lights/Taillights:

   

   Rear side-marker lights:

   

6. Install the new bulb in the reverse order of the removal procedure.

Reverse lights

4-Door

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Pull the center of each plastic retainers and remove them.

   

   1. Removal
   2. Installation
3. Remove the trunk lid trim.
4. Disconnect the electrical connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

   

5. Turn the socket and bulb assembly counterclockwise and remove it.
6. Disconnect the bulb from the socket.

   

7. Install the new bulb in the reverse order of the removal procedure.

5-Door

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Pull the center of each plastic retainer and remove the retainers.

   

   1. Removal
   2. Installation
3. Remove the trunk lid trim.
4. Disconnect the connector from the socket.

   

5. Turn the socket and bulb assembly counterclockwise and remove it.
6. Disconnect the bulb from the socket.

   

7. Install the new bulb in the reverse order of the removal procedure.

License plate lights

4-Door

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Pull the center of each plastic retainers and remove them.

   

   1. Removal
   2. Installation
3. Peel back the trunk lid trim.
4. Turn the socket and bulb assembly counterclockwise and remove it.
5. Disconnect the bulb from the socket.

   

6. Install the new bulb in the reverse order of the removal proce- dure.

5-Door

1. Make sure the ignition is switched off, and the headlight switch is off.
2. Wrap a flathead screwdriver with a soft cloth to prevent damage to the light unit.
3. Insert a flathead screwdriver into the position shown in the figure and pull the light unit outward.

   

4. Disconnect the connector from the bulb by pressing the tab on the connector with your finger and pulling the connector.

   

5. Turn the socket and bulb assembly counterclockwise and remove it.
6. Disconnect the bulb from the socket.

   

7. Install the new bulb in the reverse order of the removal procedure.

Headlights/Daytime running lights (With LED headlights), Side turn signal lights (if equipped), High-mount brake light

The LED bulb cannot be replaced as a single unit because it is an integrated unit. The LED bulb has to be replaced with the unit. We recommend your Toyota dealer when the replacement is necessary.

Headlights/Daytime running lights

• To replace the bulb, contact your Toyota dealer.
• If the halogen bulb is accidentally touched, it should be cleaned with rubbing alcohol before being used.
• Use the protective cover and carton of the replacement bulb to dispose of the old bulb promptly out of the reach of children.
• When reinstalling the sealing cover, make sure it is fitted correctly.

Replacing Interior Light Bulbs

Overhead lights/Map lights

1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens, and then remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.

   

3. Install the new bulb in the reverse order of the removal procedure.

Trunk light (4-Door)

1. Press both sides of the lens cap to remove it.
2. Disconnect the bulb by pulling it out.

   

3. Install the new bulb in the reverse order of the removal procedure.

Luggage compartment light (5-Door)

1. Wrap a small flathead screwdriver with a soft cloth to prevent damage to the lens and remove the lens by carefully prying on the edge of the lens with the flathead screwdriver.
2. Disconnect the bulb by pulling it out.

   

3. Install the new bulb in the reverse order of the removal procedure.