“POWER” switch, Transmission and Parking brake
Push button start system
The push button start system is used tostart or stop the hybrid system and select“ACC”, “IG−ON” or “OFF” mode. (See“—Selecting the push button start systemmode” on page 140 and “How to start thehybrid system” on page 350.) The systemcontains the following components.
1. “POWER” switch
2. Key slot
3. Brake pedal
4. Electronic shift lever
Key slot
Your vehicle keys and the key slot aredifferent shapes from conventional ones.Keep the following in mind when operatingthe key:
- When inserting the key, be sure topush it in all the way.
- When pulling out the key, be carefulbecause it will be pushed out by thespring and it might fly out.
- If the key cannot be pulled out, pushit in all the way again, then pull it out.
CAUTION
Do not put your finger into the keyslot. Your finger might be injured.
NOTICE
Observe the following instructions, orthe key mechanism might be damagedand will not work properly.
The key should be operated with aclean hand and fingers.
- Do not insert the key forcibly.
- Do not insert any key other thangenuine formal keys into the keyslot.
- Do not pull out the key forciblywhen it cannot be removed.
- Do not put water, oil, foreign objects,etc. into the key slot.
- Do not insert a wet, oily or damagedkey into the key slot.
- Do not affix a sticker on the key.
- Do not insert the key in the wrongway.
- Do not pull out the key ring whenremoving the key out of the keyslot.
Should you find anything unusual,contact your Toyota dealer as soon aspossible.
“POWER” switch
Press the “POWER” switch slowly andsurely. Quick operation may not activatethe desired mode.
CAUTION
- Do not press the switch while driving,except in an emergency.
- In hot weather, the switch surfacemay get hot. Take care not to getburned.
NOTICE
Observe the following instructions orthe push button start system may notwork properly.
- The switch should be operated witha clean finger. Do not use an oilyor dirty finger.
- Be careful not to spill water or otherliquid on the switch.
In the following conditions, contactyour Toyota dealer as soon as possible.
- If the indicator on the switchflashes in amber, the system maybe malfunctioning. Once you turnthe power off, it may not turn onagain.
- If you find anything unusual in theswitch function, refrain from usingthe vehicle.
In the following condition, have yourvehicle inspected by your Toyota dealer.
- The indicator light on the “POWER”switch does not come on when theclearance lights are turned on.
Selecting the push buttonstart system mode(with smart function—on some models)
Without depressing the brake pedal
Carrying a smart key allows you to operatethe “POWER” switch without thekey being inserted into the key slot.
Each time you press the “POWER”switch briefly without the brake pedaldepressed, the hybrid system modechanges in the order of “OFF”, “ACC”,“IG−ON” and then back to “OFF”.
The smart function can be set to becomeinoperative using the smart cancel switch.For details, see “Deactivating the smartfunction” on page 34.
1) “ACC” (Green indicator is turned on)
Accessories such as the radio operate.
Pressing the “POWER” switch briefly withoutdepressing the brake pedal in the“OFF” mode turns on this mode.
In the “ACC” mode, pressing the “POWER”switch briefly while depressing thebrake pedal will start the hybrid system.
If you leave your vehicle in the “ACC”mode for about an hour, the hybrid systemis automatically turned off.
2) “IG−ON” (Amber indicator is turnedon)
All accessories are operable.
Pressing the “POWER” switch briefly withoutdepressing the brake pedal in the“ACC” mode turns on this mode.
In the “IG−ON” mode, pressing the “POWER”switch briefly while depressing thebrake pedal will start the hybrid system.However, if “N” position is selected, thehybrid system will be turned to the “OFF”mode.
3) “OFF” (Indicator is turned off)
The hybrid system is off.
You may hear a motor sound in the enginecompartment for a few seconds afterthe system is turned off and about 90seconds have passed.
The hybrid vehicle immobilizer system isautomatically set. See “Hybrid vehicle immobilizersystem” on page 21.
With the brake pedal depressed
The hybrid system will start and stopby pressing the “POWER” switch brieflywith the brake pedal depressed.
You may hear a motor sound in the enginecompartment when the brake pedal isdepressed with the hybrid system off.
1) “START” (Amber indicator comes onfor a few seconds.)
The hybrid system is ready to operateand all accessories are operable. (“IG−ON”)
Press the “POWER” switch with the brakepedal depressed.
For starting tips, see “How to start thehybrid system—” on page 350.
If in an emergency, you must turn thehybrid system off while the vehicle ismoving, press the “POWER” switch formore than 3 seconds. At this time, the“ACC” mode and shift position “N” areautomatically enabled.
2) “OFF” (Indicator is turned off)
The hybrid system is off.
You may hear a motor sound in the enginecompartment for a few seconds afterthe system is turned off and about 90seconds have passed.
The hybrid vehicle immobilizer system isautomatically set. See “Hybrid vehicle immobilizersystem” on page 21.
Approximately 5 hours after the hybridsystem is turned off, you may hear asound coming from underneath the luggagecompartment for several minutes.This is normal operation and does notindicate a malfunction. (See “Leak detectionpump” on page ix.)
NOTICE
- The hybrid system cannot bestarted when the shift position is in“N”. Be sure to put it in “P” andthen start the system.
- Do not leave the hybrid system in“ACC” or “IG−ON” for a long time.The 12 volt battery will discharge.
- The hybrid mode in which the batteryis discharged or disconnectedis retained in memory, and thatmode is turned on when power isapplied.
When you leave your vehicle, be sure toturn the “POWER” switch off and carry thesmart key.
If you get out of your vehicle while carryinga key without turning off the “POWER”switch and then close the door, a warningtone sounds inside and beeps sound outside.
INFORMATION
You can insert a genuine key while inthe “IG−ON” mode or with the hybridsystem starting. Do not insert any keyother than genuine keys.
Selecting the push buttonstart system mode(without smart function)
Without depressing the brake pedal
Each time you press the “POWER”switch briefly without the brake pedaldepressed, the hybrid system modechanges in the order of “OFF”, “ACC”,“IG−ON” and then back to “OFF”.
1) “ACC” (Green indicator is turned on)Accessories such as the radio operate.
Pressing the “POWER” switch briefly withoutdepressing the brake pedal in the“OFF” mode turns on this mode.
The key can be removed at this position.The hybrid system is automatically turnedoff.
In the “ACC” mode, pressing the “POWER”switch briefly while depressing thebrake pedal will start the hybrid system.
If you leave your vehicle in the “ACC”mode for about an hour, the hybrid systemis automatically turned off.
2) “IG−ON” (Amber indicator is turnedon)
All accessories are operable.
Pressing the “POWER” switch briefly withoutdepressing the brake pedal in the“ACC” mode turns on this mode.
In the “IG−ON” mode, pressing the“POWER” switch briefly while depressingthe brake pedal will start the hybrid system.However, if “N” position is selected,the hybrid system will be turned in the“OFF” mode.
3) “OFF” (Indicator is turned off)
The hybrid system is off. The key canbe removed at this position.
You may hear a motor sound in the enginecompartment for a few seconds afterthe system is turned off and about 90seconds have passed.
Once you remove the key, the hybrid vehicleimmobilizer system is automaticallyset. See “Hybrid vehicle immobilizer system”on page 21.
With the brake pedal depressed
The hybrid system will start and stopby pressing the “POWER” switch brieflywith the brake pedal depressed.
You may hear a motor sound in the enginecompartment when the brake pedal isdepressed with the hybrid system off.
1) “START” (Amber indicator comes onfor a few seconds)
The hybrid system is ready to operateand all accessories are operable. (“IG−ON”)
Insert the key and press the “POWER”switch briefly with the brake pedal depressed.
For starting tips, see “How to start thehybrid system—” on page 350.
If, in an emergency, you must turn thehybrid system off while the vehicle ismoving, press the “POWER” switch morethan 3 seconds. At this time, the “ACC”mode and shift position “N” are automaticallyenabled.
2) “OFF” (Indicator is turned off)
The hybrid system is off. The key canbe removed at this position.
You may hear a motor sound in the enginecompartment for a few seconds afterthe system is turned off and about 90seconds have passed.
Once you remove the key, the hybrid vehicleimmobilizer system is automaticallyset. See “Hybrid vehicle immobilizer system”on page 21.
Approximately 5 hours after the hybridsystem is turned off, you may hear asound coming from underneath the luggagecompartment for several minutes.
This is normal operation and does notindicate a malfunction. (See “Leak detectionpump” on page ix.)
NOTICE
- The hybrid system cannot bestarted when the shift position is in“N”. Be sure to put it in “P” andthen start the system.
- Do not leave the hybrid system in“ACC” or “IG−ON” for a long time.The 12 volt battery will discharge.
- The hybrid mode in which the batteryis discharged or disconnectedis retained in memory, and thatmode is turned on when power isapplied.
Hybrid transaxle
Your hybrid transaxle has an electronicshift lever system to minimize incorrectoperation. This means you can only shiftto other position from “P” when the brakepedal is depressed.
With the following improper shifting, therejection function operates and a beepsounds so the hybrid transaxle cannot beshifted.
(i) When you attempt to shift the transaxlefrom the “P” position without depressingthe brake pedal.
(ii) When you push the “P” switch whiledriving.
(iii) When you operate the shift lever from“D” to “R” or vice versa while the vehicleis moving.
(iv) When you operate the shift lever to “B”from any position other than “D”.
In case of (i), the transaxle remains in“P”. In case of (ii) through (iv), the transaxleis automatically shifted to “N”.
(a) Shift lever
The shift position is displayed on the instrumentcluster.
R: Reverse position (buzzer sounds)
N: Neutral position
D: Normal driving position
B: Engine braking position(shown only while in “D”)
NOTICE
Observe the following instructions.Otherwise, the lever may cause a malfunction,resulting in trouble:
- Do not remove the knob on the lever.
- Do not use a knob other than theoriginally fitted knob.
- Do not hang anything on the lever.
Should you find anything unusual,contact your Toyota dealer as soon aspossible.
(b) “P” position switch
The “P” (parking) position is displayed onthe instrument cluster, and the indicatoron the “P” position switch comes on.
(c) Normal driving
1. Start the hybrid system as instructed in“How to start the hybrid system” onpage 350.
2. With your foot holding down the brakepedal, shift the shift lever to “D”.
CAUTION
Never put your foot on the acceleratorpedal while shifting. Doing so cancause abrupt acceleration.
3. Release the parking brake and brakepedal. Depress the accelerator pedalslowly for smooth starting.
When you shift the transaxle to “D”while backing up, an alarm sounds andthe transaxle is shifted to “N”.
(d) Using engine braking
To use engine braking, shift the shift leverto “B” position.
During high speed driving, you may feelthat deceleration by engine braking is lessthan that of a typical vehicle.
Do not continue normal driving with thetransaxle in “B” for a long time. This maycause decreased fuel economy. To preventthis, use “D” for normal driving.
When you shift the transaxle to “B” froma position other than “D”, an alarm soundsand the transaxle is automatically shiftedto “N”.
CAUTION
Be careful when downshifting on aslippery surface. Abrupt shiftingcould cause the vehicle to skid orspin.
(e) Backing up
1. Bring the vehicle to a complete stop.
2. With the brake pedal held down withyour foot, shift the shift lever to the“R” position. You will hear beeps whilethe transaxle is in “R”.
When you shift the transaxle to “R” whiledriving, an alarm sounds and the transaxleis shifted to “N”.
(f) Parking
1. Bring the vehicle to a complete stop.
2. With the brake pedal pressed down,fully depress the parking brake pedalto apply the parking brake securely.
3. With the brake pedal pressed down,push the “P” position switch.
If you press the “POWER” switch whilestopping, the transaxle is automaticallyshifted to the “P” and the hybrid systemis turned off.
If the driver’s door is opened when thetransaxle is in “N”, “D” or “B”, beepsounds and a warning message appearson the multi−information display to warnyou to shift the transaxle to “P”.
If you push the “P” position switch whiledriving, an alarm sounds and the transaxleis automatically shifted to “N”.
NOTICE
Be sure to put the hybrid transaxle in“P” when parking. In “N”, the hybridbattery will not be charged even if thegasoline engine is running. You cannotstart your vehicle if the transaxleis left in “N” for a long time becausethe hybrid battery will discharge.
When shifting the transaxle from “P” onthe slope, a large parking lock releasingnoise will be generated. However, thisdoes not indicate a malfunction.
(g) Vehicle driving characteristics
Creeping
In order to hold the vehicle properly on anincline and for better accelerator pedaloperation at starting, your vehicle is designedlike a typical automatic transmissionvehicle which tends to move withoutdepressing the accelerator pedal with thetransaxle in a position other than “P” or“N”.
With the transaxle in a position other than“P” or “N”, depress the brake pedal firmlyeven when stopped and apply the parkingbrake as required.
When moving in a compact area or duringa traffic jam, it is an effective way tocontrol the speed using only the brakepedal operation without depressing the acceleratorpedal.
Regenerative brake
When the accelerator pedal is released orthe brake pedal is depressed, the electricmotor acts as a generator and convertskinetic energy to electric energy to providedeceleration and recover electric energy tocharge the hybrid battery.
At this time, the electric motor runningnoise may increase.
The operation is the same as a typicalgasoline powered vehicle.
You may experience the following conditionwhile braking. As they do not indicatea malfunction, perform braking as usual:
In the “OFF” mode, pressing the“POWER” switch once or twice will select“ACC” or “IG−ON” only if the brakepedal is not depressed. In this condition,the brake pedal may move a little.
Hybrid driving
This vehicle runs in combination with thegasoline engine and electric motor.
If the “READY” light is on, you can startyour vehicle even with the gasoline enginestopped.
(h) If the system malfunctions
In the following conditions, there is someproblem in the system.
- The indicator on the “P” position switchflashes. However, this does not indicatea malfunction unless a warningmessage appears in the multi−informationdisplay.
- All frames of shift position indicators inthe instrument cluster flash.
- The parking system error message appearson the multi−information display.
- The instrument cluster and multi−informationdisplay does not come on whenthe “IG−ON” mode is enabled.
In these cases, stop your vehicle in asafe and level place, apply the parkingbrake securely and contact your Toyotadealer immediately.
(i) When the 12 volt battery is disconnected
Before you disconnect the 12 volt battery,confirm the shift position is “P” and applythe parking brake completely.
After you reconnect the 12 volt battery,shift the shift lever to “N” and confirm theshift position is in “N” when the “IG−ON”mode is enabled.
Vehicle stability control system
The vehicle stability control systemhelps provide integrated control of thesystems such as anti−lock brake system,brake assist system, hybrid systemcontrol, etc. This system automaticallycontrols the brakes and hybrid systemto help prevent the vehicle from skiddingwhen cornering on a slippery roadsurface or operating steering wheelabruptly.
The vehicle stability control system is activatedwhen the vehicle speed is morethan about 15 km/h (9 mph).
CAUTION
Do not rely exclusively on the vehiclestability control system. Evenif the vehicle stability control systemis operating, you must alwaysdrive carefully and attentively toavoid death or serious injury. Recklessdriving will result in an unexpectedaccident. If the slip indicatorlight flashes, sounding an alarm,special care should be taken whiledriving.
Only use tires of specified size. Thesize, manufacturer, brand and treadpattern for all 4 tires should be thesame. If you use tires other thanspecified, or mixed types or size,the vehicle stability control systemmay not function correctly. Whenreplacing the tires or wheels, contactyour Toyota dealer. (See“Checking and replacing tires” onpage 411.)
Slip indicator light
If the vehicle is going to skid during driving,the slip indicator light blinks and analarm sounds intermittently. Special careshould be taken while driving.
The slip indicator light blinks in the followingconditions also.
- The vehicle tires are racing. Utmostcare is required when driving.
- When the anti−lock brake system isoperating. See “Brake system” on page327 for details.
The slip indicator light comes on when the“IG−ON” mode is enabled and will go offafter the “READY” light comes on. If theindicator light does not come on when thehybrid system is turned on, contact yourToyota dealer.
“VSC” warning light
This light warns that there is a problemsomewhere in the vehicle stability controlsystem.
The light will come on when the “IG−ON”mode is enabled and will go off after the“READY” light comes on.
If the light comes on while driving, thesystem does not work. However, becausethe conventional braking still operates, youcan drive your vehicle without damagingit. Contact your Toyota dealer.
In the following cases, contact your Toyotadealer:
The warning light does not come onafter the “IG−ON” mode is enabled.
The warning light remains on after the“READY” light comes on.
The warning light comes on while driving.
Tire pressure warning system
The tire pressure warning system warnsyou that the tire inflation pressure islow.
The tire pressure warning system is nota substitute for checking normal tire inflationpressure. Check the tire inflationpressure with a tire pressure gauge regularly.
CAUTION
The warning system may not activateimmediately if bursts or sudden airleakage should occur.
The tire pressure warning light comes onwhen the “POWER” switch is selected in“IG−ON” mode and goes off after a fewseconds. This means the tire pressurewarning light is operating properly. If thetire inflation pressure becomes low, thelight comes on again. In this case, adjustingthe tire inflation pressure will turn offthe light after a few minutes. If the lightcomes on after blinking for 1 minute, thetire pressure warning system is not workingproperly.
CAUTION
If the tire pressure warning lightcomes on, be sure to observe thefollowing precautions. Failure to doso could cause loss of vehicle controland result in death or serious injury.
- Stop your vehicle in a safe place assoon as possible. Adjust the tireinflation pressure immediately.
- If the tire pressure warning lightcomes on even after tire inflationpressure adjustment, it is probablethat you have a flat tire. Check thetires. If the tire is flat, change tothe spare tire and have the flat tirerepaired by the nearest Toyota dealer.
- Avoid abrupt maneuvering and braking.If the vehicle tires deteriorate,you could lose control of the steeringwheel or the brakes.
The tire pressure warning light may turnon due to natural causes such as naturalair leaks or tire inflation pressure changescaused by temperature. In this case, adjustingthe tire inflation pressure will turnoff the light after a few minutes.
Pushing the tire pressure warning resetswitch should not turn off the tire pressurewarning light. Adjusting the tire inflationpressure will turn off the light.
The compact spare tire is not equippedwith the tire pressure warning valve andtransmitter. If a tire goes flat, the warninglight will not turn off even though the flattire is replaced with the spare tire. Replacethe spare tire with the repaired tireand adjust the proper tire inflation pressure.The tire pressure warning light will turnoff after a few minutes.
CAUTION
Each tire, including the spare (if provided),should be checked monthlywhen cold and inflated to the inflationpressure recommended by the vehiclemanufacturer on the vehicle placardor tire inflation pressure label (tireand load information label). (If yourvehicle has tires of a different sizethan the size indicated on the vehicleplacard or tire inflation pressure label(tire and load information label), youshould determine the proper tire inflationpressure for those tires.)
As an added safety feature, your vehiclehas been equipped with a tirepressure monitoring system (TPMS–tire pressure warning system) that illuminatesa low tire pressure telltale(tire pressure warning light) when oneor more of your tires is significantlyunder−inflated. Accordingly, when thelow tire pressure telltale (tire pressurewarning light) illuminates, youshould stop and check your tires assoon as possible, and inflate them tothe proper pressure. Driving on a significantlyunder−inflated tire causesthe tire to overheat and can lead totire failure. Under−inflation also reducesfuel efficiency and tire treadlife, and may affect the vehicle’s handlingand stopping ability.
Please note that the TPMS (tire pressurewarning system) is not a substitutefor proper tire maintenance, andit is the driver’s responsibility tomaintain correct tire pressure, even ifunder−inflation has not reached thelevel to trigger illumination of theTPMS low tire pressure telltale (tirepressure warning light).
NOTICE
Do not use liquid sealants for a flattire as tire pressure warning valveand transmitter will be damaged.
When the tires must be repaired orreplaced, have them repaired or replacedby the nearest Toyota dealeror an authorized tire dealer. Thetire pressure warning valves andtransmitters will be affected by theinstallation or removal of tires.
IF THE TIRE PRESSURE WARNINGLIGHT COMES ON AFTER BLINKINGFOR 1 MINUTE...
If the tire pressure warning light comeson after blinking for 1 minute when the“POWER” switch is selected in “IG−ON”mode, the tire pressure warning systemis not working properly.
The system will be disabled in the followingconditions:
(When the condition becomes normal, thesystem will work properly.)
- If tires not equipped with tire pressurewarning valves and transmitters areused.
- If the ID code on the tire pressure warningvalves and transmitters is not registeredon the tire pressure warning ECU.
- If electronic devices or facilities usingsimilar radio wave frequencies arenearby.
- If a radio set at similar frequencies isin use in the vehicle.
- If a window tint that affects the radiowave signals is installed.
- If there is a lot of snow or ice on thevehicle, in particular around the wheelsor wheel housings.
- If non−genuine Toyota wheels are used.
- If tire chains are used.
- If the tire inflation pressure is morethan 500 kPa (5.1 kgf/cm2 or bar, 73psi) or higher.
If the tire pressure warning light continuesto come on after blinking for 1 minutewhen the “POWER” switch is selected in“IG−ON” mode, have the system checkedby your Toyota dealer.
Even if you use genuine wheels, the tirepressure warning system may not workproperly with some types of tires.
Pushing the tire pressure warning resetswitch should not turn off the tire pressurewarning light.
REPLACING TIRES AND WHEELS
When replacing the tires and wheels, besure to install tire pressure warning valvesand transmitters. ID codes on the tirepressure warning valves and transmittersare registered on the tire pressure warningECU. When replacing a tire pressurewarning valve and transmitter, it is necessaryto register the ID code of tire pressurewarning valve and transmitter. Havethe ID code registered by your Toyotadealer.
If the ID code is not registered, the systemwill not work properly. After about 1hour, the tire pressure warning lightcomes on after blinking for 1 minute toindicate a system malfunction.
NOTICE
When the tires or tire pressure warningvalves and transmitters must bereplaced, have them replaced by yourToyota dealer. The tire pressure warningvalves and transmitters will beaffected by the installation or removalof tires.
Tire pressure warning reset switch
When initializing the system, the presenttire inflation pressure is stored as standard.The tire pressure warning systemdetermines decreased air pressure bycomparing the present and the standardtire inflation pressures. When you changethe set tire inflation pressure, it is necessaryto initialize the tire pressure warningsystem.
When rotating the tires on vehicles differingwith front and rear tire inflationpressures.
When changing the tire size.
To initialize the system, perform the following:
1. Park the vehicle in a safe place andthe hybrid system is off.
2. Adjust the pressure of all the installedtires to the specified cold tire inflationpressure level. (See “Tires” on page434.)
3. Turn the “POWER” switch to “IG−ON”mode.
4. Push and hold the tire pressure warningreset switch until the tire pressurewarning light blinks slowly three times.
5. Wait for a few minutes with the “POWER”switch selected in “IG−ON” mode,and then turn the hybrid system off.
If you push the tire pressure reset switchwhile the vehicle is moving, initialization isnot performed.
If you push the tire pressure reset switchaccidentally and initialization is performed,adjust the tire inflation pressure to thespecified level and initialize the systemagain.
If the tire pressure warning light does notblink slowly three times when you pushand hold the reset switch, initialization hasfailed and the tire pressure warning systemmay not work properly. In this case,initialize the system again. If initializationcannot be performed, have the systemchecked at your Toyota dealer.
CAUTION
Do not push the reset switch withoutfirst adjusting the tire inflation pressureto the specified level. Otherwise,the tire pressure warning light maynot come on even if the tire inflationpressure is low, or it may come onwhen the tire inflation pressure is actuallynormal.
Parking brake
Vehicles sold in the U.S.A.
Vehicles sold in Canada
When parking, firmly apply the parkingbrake to avoid inadvertent creeping.
To set: Fully depress the parking brakepedal. For better holding power, first depressthe brake pedal and hold it whilesetting the parking brake.
To release: Depress the parking brakepedal while depressing the brake pedal.
To remind you that the parking brake isset, the parking brake reminder light inthe instrument panel remains on until yourelease the parking brake.
CAUTION
- Driving with the parking brake engagedcan reduce braking power.
- Before driving, be sure the parkingbrake is fully released and the parkingbrake reminder light is off.
Cruise control
The cruise control allows you to cruisethe vehicle at a desired speed over 40km/h (25 mph) even with your foot offthe accelerator pedal.
Your cruising speed can be maintained upor down grades within the limits of hybridsystem performance, although a slightspeed change may occur when driving upor down the grades. On steeper hills, agreater speed change will occur so it isbetter to drive without the cruise control.
CAUTION
To help maintain maximum controlof your vehicle, do not use thecruise control when driving inheavy or varying traffic, or on slippery(rainy, icy or snow–covered) orwinding roads.
Avoid vehicle speed increases whendriving downhill. If the vehiclespeed is too fast in relation to thecruise control set speed, cancel thecruise control then shift the shiftlever to “B” position to use enginebraking to slow down.
TURNING THE SYSTEM ON
To operate the cruise control, push the“ON·OFF” switch. This turns the systemon. The indicator light in the instrumentpanel shows that you can now set thevehicle at a desired cruising speed. Anotherpush on the switch will turn the systemcompletely off.
CAUTION
To avoid accidental cruise control engagement,keep the “ON·OFF” switchoff when not using the cruise control.
SETTING AT A DESIRED SPEED
The transaxle must be in “D” before youset the cruise control speed.
Bring your vehicle to the desired speed,push the lever down in the “– SET” directionand release it. This sets the vehicleat that speed.
If the speed is not satisfactory, tap thelever up for a faster speed, or tap it downfor a slower speed. Each tap changes theset speed by 1.6 km/h (1.0 mph). You cannow take your foot off the acceleratorpedal.
If you need acceleration—for example,when passing—depress the acceleratorpedal enough for the vehicle to exceedthe set speed. When you release it, thevehicle will return to the speed set priorto the acceleration.
CANCELING THE PRESET SPEED
You can cancel the preset speed by:
a. Pulling the control lever in the“CANCEL” direction and releasing it.
b. Depressing the brake pedal.
If the vehicle speed falls below about 40km/h (25 mph), the preset speed will automaticallycancel out.
If the vehicle speed drops 16 km/h (10mph) below the preset speed, the presetspeed will also automatically cancel out.
If the preset speed automatically cancelsout other than for the above cases, haveyour vehicle checked by your Toyota dealerat the earliest opportunity.
RESETTING TO A FASTER SPEED
Push the lever up in the “+ RES” directionand hold it. Release the lever when thedesired speed is attained. While the leveris held up, the vehicle will gradually gainspeed.
However, a faster way to reset is to acceleratethe vehicle and then push thecontrol lever down in the “– SET” direction.
RESETTING TO A SLOWER SPEED
Push the lever down in the “– SET” directionand hold it. Release the lever whenthe desired speed is attained. While thelever is held down, the vehicle speed willgradually decrease.
However, a faster way to reset is to depressthe brake pedal and then push thecontrol lever down in the “– SET” direction.
RESUMING THE PRESET SPEED
If the preset speed is cancelled by pullingthe control lever or by depressing thebrake pedal, pushing the lever up in the“+ RES” direction will restore the speedset prior to cancellation.
However, once the vehicle speed falls belowabout 40 km/h (25 mph), the presetspeed will not be resumed.
CRUISE CONTROL FAILURE WARNING
If the “CRUISE” indicator light in theinstrument cluster flashes when using thecruise control, press the “ON·OFF” buttonto turn the system off and then press itagain to turn it on.
If any of the following conditions then occurs,there is some trouble in the cruisecontrol system.
- The indicator light does not come on.
- The indicator light flashes again.
- The indicator light goes out after itcomes on.
If this is the case, contact your Toyotadealer and have your vehicle inspected.
Download Manual