Automatic High Beam
The Automatic High Beam uses an in-vehicle front camera to assess the brightness of streetlights, the lights of vehicle ahead, etc., and automatically turns the high beam on or off as necessary.
Activating the Automatic High Beam system
1 Push the lever away from you with the headlight switch in the or position.
2 Press the Automatic High Beam switch.
The Automatic High Beam indicator will come on when the headlights are turned on automatically to indicate that the system is active.
High beam automatic turning on or off conditions
When all of the following conditions are met, the high beam will be automatically turned on (after approximately 1 second):
- Vehicle speed is above approximately 21 mph (34 km/h).
- The area ahead of the vehicle is dark.
- There are no vehicles ahead with headlights or tail lights turned on.
- There are few streetlights on the road ahead.
If any of the following conditions are met, the high beam will be automatically turned off:
- Vehicle speed drops below approximately 17 mph (27 km/h).
- The area ahead of the vehicle is not dark.
- Vehicles ahead have headlights or tail lights turned on.
- There are many streetlights on the road ahead.
Turning the high beam on/off manually
Switching to high beam
Pull the lever to the original position.
The Automatic High Beam indicator will turn off.
Push the lever away from you to activate the Automatic High Beam system again.
Switching to low beam
Press the Automatic High Beam switch.
The AHB indicator will turn off.
Press the switch to activate the Automatic High Beam system again.
The Automatic High Beam can be operated when
The engine switch is in IGNITION ON mode.
Camera sensor detection information
High beam may not be automatically turned off in the following situations:
- When oncoming vehicles suddenly appear from a curve
- When the vehicle is cut in front of by another vehicle
- When oncoming or preceding vehicles are hidden from sight due to repeatedcurves, road dividers or roadside trees
High beam may be turned off if an oncoming vehicle that is using fog lights withoutusing the headlights is detected.
House lights, street lights, red traffic signals, and illuminated billboards or signs maycause the high beam to turn off.
The following factors may affect the amount of time taken to turn high beam on or off:
- The brightness of headlights, fog lights, and tail lights of oncoming and precedingvehicles
- The movement and direction of oncoming and preceding vehicles
- When an oncoming or preceding vehicle only has operational lights on one side
- When an oncoming or preceding vehicle is a two-wheeled vehicle
- The condition of the road (gradient, curve, condition of the road surface etc.)
- The number of passengers and amount of luggage
High beam may be turned on or off when unexpected by the driver.
Small vehicles, such as bicycles, may not be detected.
In the situations below, the system may not be able to correctly detect the surroundingbrightness levels, and may flash or expose nearby pedestrians to the high beam. There-fore, you should consider turning the high beams on or off manually rather than relyingon the Automatic High Beam system.
-
In bad weather (rain, snow, fog, sandstorms etc.)
-
The windshield is obscured by fog, mist, ice, dirt etc.
-
The windshield is cracked or damaged.
-
The camera sensor is deformed or dirty.
-
Surrounding brightness levels are equal to those of headlights, tail lights or fog lights.
-
Vehicles ahead have headlights or tail lights that are either switched off, dirty, chang-ing color, or have improperly adjusted aim.
-
When driving through an area of intermittently changing brightness and darkness.
-
When frequently and repeatedly driving ascending/descending roads, or roads withrough, bumpy or uneven surfaces (such as stone-paved roads, gravel tracks etc.).
-
When frequently and repeatedly taking curves or driving on a winding road.
-
There is a highly reflective object ahead of the vehicle, such as a sign or a mirror.
-
The vehicle’s headlights are damaged or dirty.
-
The vehicle is listing or titling, due to a flat tire, a trailer being towed etc.The driver believes that the high beam may be causing problems or distress to otherdrivers or pedestrians nearby.
Temporarily lowering sensor sensitivity
The sensitivity of the sensor can be temporarily lowered.
1. Turn the engine switch off while the following conditions are met.
- The headlight switch is in or .
- The headlight switch lever is in high beam position.
- Automatic High Beam switch is on.
2. Turn the engine switch to IGNITION ON mode.
3. Within 5 seconds after , repeat pulling the headlight switch lever to the originalposition then pushing it to the high beam position quickly 9 times, then leave thelever in high beam position.
Automatic High Beam (headlights) may turn on even the vehicle is stopped.
CAUTION
Limitations of the Automatic High Beam
Do not rely on the Automatic High Beam. Always drive safely, taking care to observeyour surroundings and turning high beam on or off manually if necessary.
Download Manual