Lighting
This vehicle is equipped with a variety of lights to illuminate the interior and exterior of the vehicle.
CAUTION
To prevent the battery from being discharged, do not leave the headlamp and interior light on for a prolonged time while the engine is not running.
Battery saver function
The purpose of this feature is to prevent the battery from being discharged if the lights are left in the ON position. The system automatically shuts off the parking light 30 seconds after the vehicle is turned off and the driver's door is opened and closed.
With this feature, the parking light will turn off automatically if the driver parks on the side of the road at night and opens the driver's side door.
If necessary, to keep the parking light on when the vehicle is turned off, perform the following:
1. Open the driver-side door.
2. Turn the parking light OFF and ON again using the light switch on the steering column.
Headlamp delay function
If you place the ignition switch or ENGINE START/STOP button in the ACC or OFF position with the headlamps ON, the headlamps (and/or parking lights) remain on for about 5 minutes. However, with the engine off if the driver's door is opened and closed, the headlamps (and/or parking lights) are turned off after 15 seconds.
The headlamps (and/or parking lights) can be turned off by pressing the lock button on the remote key or smart key twice or turning the light switch to the OFF or AUTO position. However, if you turn the light switch to the AUTO position when it is dark outside, the headlamps will not be turned off.
You can activate or deactivate the Headlamp Delay function from the User Settings Mode in the LCD display. For more details, refer to "User settings mode" on page 4-97. If your vehicle is equipped with additional navigation, please refer to the infotainment system manual separately supplied.
NOTICE
If the driver exits the vehicle through another door besides the driver door, the battery saver function does not operate and the headlamp delay function does not turn OFF automatically. This may cause the battery to discharge. To avoid battery discharge, turn OFF the headlamps manually from the headlamp switch before exiting the vehicle.
Daytime Running Light (DRL) (if equipped)
The Daytime Running Light (DRL) can make it easier for others to see the front of your vehicle during the day.
The DRL can be helpful in many different driving conditions, and it is especially helpful after dawn and before sunset.
The DRL will turn the dedicated lamp OFF when:
- Position & Taillamp switch is on.
- The vehicle is off.
- The front fog light is on. (if equipped)
- Engaging the parking brake.
Lighting control
The light switch has a headlamp and a position lamp position.
To operate the lights, turn the knob at the end of the control lever to one of the following positions:
1. OFF position
2. Auto light position
3. Position & Taillamp
4. Headlamp position
Position & Taillamp
When the light switch is in the position lamp position, the front position lamp, taillamp, and the license plate lamp will turn ON.
Headlamp (Low Beam)
When the light switch is in the headlamp position, headlamp (low beam), tail, license light will turn ON.
NOTICE
The ignition switch or ENGINE START/STOP button must be in the ON position to turn on the headlamps.
Auto light
When the light switch is in the AUTO light position, the taillamps and headlamps will turn ON or OFF automatically depending on the amount of light outside the vehicle.
CAUTION
- Never place anything over the sensor (1) located on the instrument panel as this will ensure better auto-light system control.
- Don't clean the sensor using a window cleaner, the cleaner may leave a light film which could interfere with sensor operation.
- If your vehicle has window tint or other types of metallic coating on the front windshield, the Auto light system may not work properly.
Operating high beam
To turn on the high beam headlamp:
- Push the lever away from you. The lever will return to its original position. The high beam indicator will light when the headlamp high beams are switched on.
To flash the headlamps:
- Pull the lever towards you.
It will return to the normal (low beam) position when released. The headlamp switch does not need to be on to use this flashing feature.
Operating turn signals and lane change signals
The ENGINE START/STOP button must be on for the turn signals to function.
To turn on the turn signals:
- Move the lever up or down (A). The green arrow indicators on the instrument panel indicate which turn signal is operating. They will self-cancel after a turn is completed. If the indicator continues to flash after a turn, manually return the lever to the OFF position.
To signal a lane change:
- Move the turn signal lever slightly and hold it in position (B). The lever will return to the OFF position when released.
If an indicator stays on and does not flash or if it flashes abnormally, one of the turn signal bulbs may be burned out and will require replacement.
One-touch lane change function
To activate a one-touch lane change function, move the turn signal lever slightly and then release it. The lane change signals will blink 3, 5 or 7 times.
You can activate or deactivate the One Touch Turn Signal function or choose the number of blinking (3, 5, or 7) by selecting "User Settings → Lights → One Touch Turn Signal".
NOTICE
If an indicator flash is abnormally quick or slow, a bulb may be burned out or have a poor electrical connection in the circuit. The bulb may require replacement.
Operating front fog light (if equipped)
Fog lights are designed to provide improved visibility when visibility is poor due to fog, rain or snow, etc.
The fog lights will turn on when the fog light switch (1) is turned to the on position after the headlamp is turned on.
To turn off the fog lights:
- Turn the fog light switch (1) to the ON position.
CAUTION
When in operation, the fog lights consume large amounts of vehicle electrical power. Only use the fog lights when visibility is poor.
High Beam Assist (HBA) (if equipped)
High Beam Assist is a function that automatically adjusts the headlamp range (switches between high beam and low beam) depending on the brightness of detected vehicles and certain road conditions.
Detecting sensor
Front view camera
The front view camera is used as a detecting sensor to detect ambient light and brightness while driving. Refer to the picture above for the detailed location of the detecting sensor.
NOTICE
- Always keep the front view camera in good condition to maintain optimal performance of High Beam Assist.
- For more details on the precautions of the front view camera, refer to"Forward Collision-Avoidance Assist (FCA) (Front view camera only) (if equipped)" on page 5-79.
Function setting
With the ENGINE START/STOP button in the ON position, select 'Lights → High Beam Assist' from the Settings menu to turn on High Beam Assist and deselect to turn off the function.
WARNING
For your safety, adjust your high beam settings only after parking the vehicle at a safe location.
Function operation
Display and control
- After selecting 'High Beam Assist' in the Settings menu, High Beam Assist will operate by following the procedure below.
- Place the headlamp switch in the AUTO position and push the headlamp lever towards the instrument cluster. The High Beam Assist ( ) indicator light will illuminate on the cluster and the function will be enabled.
- When the function is enabled, high beam will turn on when vehicle speed is above 25 mph (40 km/h). When vehicle speed is below 15 mph (25 km/h), high beam will not turn on.
- The High Beam ( ) indicator light will illuminate on the cluster when high beam is on. - When High Beam Assist is operating, if the headlamp lever or switch is used, the function operates as follow:
- If the headlamp lever is pulled towards you when the high beam is off, the high beam will turn on without High Beam Assist canceled. When you let go of the headlamp lever, the lever will move to the middle and the high beam will turn off.
- If the headlamp lever is pulled towards you when the high beam is on by High Beam Assist, low beam will be on and the function will turn off.
- If the headlamp switch is placed from AUTO to another position (headlamp/position/off), High Beam Assist will turn off and the corresponding lamp will turn on. - When High Beam Assist is operating, high beam switches to low beam if any of the following conditions occur:
- When the headlamp of an oncoming vehicle is detected.
- When the taillamp of a vehicle in front is detected.
- When the headlamp or taillamp of a motorcycle or a bicycle is detected.
- When the surrounding ambient light is bright enough that high beams are not required.
- When streetlights or other lights are detected.
Malfunction and limitations
Malfunction
When High Beam Assist is not working properly, the 'Check High Beam Assist (HBA) system' warning message will appear and warning light ( ) will illuminate on the cluster. Have the function be inspected by an authorized Kia dealer.
Limitations
High Beam Assist may not work properly in the following situations:
- Light from a vehicle is not detected because of lamp damage, or because it is hidden from sight, etc.
- Headlamp of a vehicle is covered with dust, snow or water.
- A vehicle's headlamps are off but the fog lamps are on and etc.
- There is a lamp that has a similar shape as a vehicle's lamp.
- Headlamps have been damaged or not repaired properly.
- Headlamps are not aimed properly.
- Driving on a narrow curved road, rough road, uphill or downhill.
- Vehicle in front is partially visible on a crossroad or curved road.
- There is a traffic light, reflecting sign, flashing sign or mirror ahead.
- There is a temporary reflector or flash ahead (construction area).
- The road conditions are bad such as being wet, iced or covered with snow.
- A vehicle suddenly appears from a curve.
- The vehicle is tilted from a flat tire or is being towed.
- Light from a vehicle is not detected because of exhaust fume, smoke, fog, snow, etc.
NOTICE
For more details on the limitations of the front view camera, refer to
- At times, High Beam Assist may not work properly. The function is for your convenience only. It is the responsibility of the driver for safe driving practices and always check the road conditions for your safety.
- When High Beam Assist does not operate normally, change the headlamp position manually between high beam and low beam.
Download Manual